Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Nano router can connect, but no IP

< Wi-Fi Routers

Nano router can connect, but no IP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Nano router can connect, but no IP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AlanHK

2019-07-22 03:00:50 - last edited 2019-07-22 03:18:29

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-07-22

Nano router can connect, but no IP

2019-07-22 03:00:50 - last edited 2019-07-22 03:18:29

Model: TL-WR802N

Hardware Version: V1

Firmware Version:

Using a nano router, which only has a status light, an ethernet port and a reset button. This was bought in 2013. We used it for a few years, then didn't need it. Just got it out and tried to use it.

The immediate problem is that I cannot get to the admin page on the LAN, let alone the internet.

The light turns on and my laptop can see a wifi router with the default name "TP-LINK_COC590" and connect to it. However, I do not get an IP. Using an Android phone, I can choose it but it then says "Obtaining internet address" for a few minutes till it gives up. Connecting to my laptop by ethernet same result: No IP. I tried opening the web interface anyway, 192.168.1.253, per the label, also 192.168.1.0 and 192.168.1.1 but of course none could connect.

Pushed the reset and powered on and off several times, no change.

Any suggestions?

3 Reply

Kevin_Z

2019-07-23 02:17:19

Posts: 21650

Helpful: 5076

Solutions: 2555

Stories: 21

Registered: 2018-12-24

Re:Nano router can connect, but no IP

2019-07-23 02:17:19

@AlanHK

Try to setup a static IP for your computer, which in the same subnet as the default access of the router printed on the bottom label.

Click here to read the FAQ to setup static IP.

After that, try to relogin to the web UI and you can change another web browser or device as well.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

AlanHK

LV1

2019-07-23 05:13:01 - last edited 2019-07-23 05:15:49

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-07-22

Re:Re:Nano router can connect, but no IP

2019-07-23 05:13:01 - last edited 2019-07-23 05:15:49

Yes! That worked.

Then I found that the router's interface was Chinese. Managed to stumble through it to set it up anyway.

But would like to get the English firmware. I can't find any links to get it myself, this model (TL-WR800N, not 802 as I was forced to choose above) is from 2013 and they appear to have scrubbed it from their site, so I requested that from customer support. Is there any kind of firmware (and manual) archive?

Kevin_Z

2019-07-23 10:37:13

Posts: 21650

Helpful: 5076

Solutions: 2555

Stories: 21

Registered: 2018-12-24

Re:Re:Re:Nano router can connect, but no IP

2019-07-23 10:37:13

@AlanHK

The TL-WR800N is sold in mainland of China, which we are not familiar with it, please contact the tech support team as below contact info to get some help: fae@tp-link.com.cn.

Nano router can connect, but no IP

Nano router can connect, but no IP

Information

Voters 0

Tags