Archer C60 V3 QOS limitation
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello,
I bought an Wifi Archer C60 V3 and I'm surprised and disappointed about the QOS limitation compare to the V2 version .
It's just possible to give "one" prirority on each device, no more ... By port is not possible ... and by level of priority is not possible ... This version is limited ...
Is it planned or Is there a way to have the same functionality of the "V2 version" ?
Best regards,
Julien
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thanks for your requesting.
Compared to C60 V2, there are some changes, first, no different priority levels to choose, and does not support QoS by physical port. C60 v3 has changed the basic setting and improved the algorithm/logical.
You can refer to chapter 8 of the user manual to get the configuration guidance. Now it has a priority toggle available for each device and time duartion is selectable which is more flexible and more efficient.
You can give it a go to test the performance.
Best regards.
- Copy Link
- Report Inappropriate Content
Hello @Jesus-Casanova and all,
You can refer to the User Manual in Chapter 8 to set the QoS for the devices in the network:
https://static.tp-link.com/2020/202004/20200409/1910012740_Archer%20C60_UG_V3.pdf
Be aware that QoS is not a device-based speed limit, QoS is used for prioritizing the traffic when the connection is under heavy load. Check this article to know more about QoS:
- Copy Link
- Report Inappropriate Content
Thanks for your requesting.
Compared to C60 V2, there are some changes, first, no different priority levels to choose, and does not support QoS by physical port. C60 v3 has changed the basic setting and improved the algorithm/logical.
You can refer to chapter 8 of the user manual to get the configuration guidance. Now it has a priority toggle available for each device and time duartion is selectable which is more flexible and more efficient.
You can give it a go to test the performance.
Best regards.
- Copy Link
- Report Inappropriate Content
@Kevin_Z this is very disappointing if we are unable to control qos in advance option then why are you selling this device at least you have to mention that this device cannot comes with qos manual options..this is very bad cant espect.
- Copy Link
- Report Inappropriate Content
same problem with my Archer C60 V3
I can use Enable or disable QoS only, its work normally.
but if i set device priority setting ON for some device, It doesn't WORK.
i think it is very big problem, i cannot control the internet speed for other people.
please give us some software update for this problem.
thank you
- Copy Link
- Report Inappropriate Content
Buenas noches,
Hoy compre un router Archer C60 V3, y tengo el mismo problema, le doy habilitar y coloco 5 megas tanto en subida como en bajada, pero me limita todos los dispositivos.
Cuando le doy ON a un dispositivo para alta prioridad y en horario "siempre", sigo obteniendo los 5 megas, no hace la función. No me navega full, Es un error muy grave y me costo mucho dinero este router aca en Venezuela.
Consiguieron alguna solucion o alguna actualizacion de firmware?
Quedo atento, Buenas noches.
- Copy Link
- Report Inappropriate Content
Hello @Jesus-Casanova and all,
You can refer to the User Manual in Chapter 8 to set the QoS for the devices in the network:
https://static.tp-link.com/2020/202004/20200409/1910012740_Archer%20C60_UG_V3.pdf
Be aware that QoS is not a device-based speed limit, QoS is used for prioritizing the traffic when the connection is under heavy load. Check this article to know more about QoS:
- Copy Link
- Report Inappropriate Content
@Kevin_Z Buenos días no tiene sentido entonces el boton de alta prioridad y horario en la v3.
Pienso que esa no es la solucion.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2286
Replies: 6
Voters 0
No one has voted for it yet.