OneMesh for Ax6000

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

OneMesh for Ax6000

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
78 Reply
Re:OneMesh for Ax6000
2021-03-10 12:04:34

@Kevin_Z 

Ok Kevin. The extender took ages to give the note 10 an ip address. Too long to be of any use. Also 2 other devices were without internet at the same time which were very near the extender.

 

Alll were showing as unknown devices with a 0.0.0.0 ip address.

 

The xtender is now an extender only with mesh and smart connect on router turned off. It has the same wi fi names as the ax6000 and it works ok.

 

I will try on the weekend your suggestion of reinstate mesh but leave smart off.

 

 

  0  
  0  
#72
Options
Re:OneMesh for Ax6000
2021-03-11 01:35:38

@Cawsie 

 

Thank you very much for getting back with the detailed info. Kindly give it a go to disable the Smart Connect while leave the Onemesh on, then monitor again.

 

To locate this issue and try to fix it, we would like to follow up on your case via email. Please respond to the email directly if the issue persists.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#73
Options
Re:OneMesh for Ax6000-Solution
2021-03-18 08:08:40 - last edited 2021-03-18 08:08:46

@Cawsie 

 

Hi, we hope you could spend some time on the Onemesh survey, then we will better understand your requirements, thank you:

https://community.tp-link.com/en/home/forum/topic/257632

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#74
Options
Re:OneMesh for Ax6000
2021-04-11 16:46:49

@localhost192 I finally updated the software to enable OneMesh for my AX6000 and RE505X.  I have the RE505X set up as a wired access point.  There is no OneMesh in the menu for it when I checked after the firmware update of the AX6000.  What's the deal?  I switched the RE505x to extender mode and then it showed up.  Seems shortsighted to not be able to us the RE505X as a wired extender and use OneMesh at the same time.  I need a range extender because it's far away from the main router!

  0  
  0  
#75
Options
Re:OneMesh for Ax6000
2021-04-11 16:59:31
Same problem here.. with same repaeter and with Re305 too... It's a limitation but i hope that they fix it!
  0  
  0  
#76
Options
Re:OneMesh for Ax6000
2021-04-12 07:40:27

@Scott180 @ghl 

 

The OneMesh™ products can’t support the Ethernet backhaul. We currently only have Deco supports the Ethernet backhaul.

 

For more details, please refer to the below FAQ:

https://www.tp-link.com/support/faq/2690/

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#77
Options
Re:OneMesh for Ax6000
2021-04-24 12:13:29

Hi @Kevin_Z 

I have three AX 6000 and two RE605, it possible to connect  all of AX 6000 and extenders in one WiFi network with "onemesh" support, or AX 6000 works only with extenders, without possibility to works with each other?? 

Tnx for your answer,

  0  
  0  
#78
Options
Re:OneMesh for Ax6000
2021-04-25 01:01:45

@XZeal 

 

Are all the three AX6000s and two RE605s in the same location? Unfortunately, the Onemesh router can only build up the Onemesh network with the Onemesh RE or Onemesh PLC. In your situation, we think Deco mesh would be more suitable for your needs:

https://www.tp-link.com/mesh/

 

But please also keep in mind that the Onemesh devices are not compatible with Deco mesh, they cannot build up the same mesh network:

https://www.tp-link.com/support/faq/2690/

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#79
Options