Home Network Community > Wi-Fi Routers > giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
< Wi-Fi Routers

giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
2020-03-01 15:18:46 - last edited 2020-03-04 05:41:29
Model: Archer C2  
Hardware Version: V1
Firmware Version:

Hi, 

 

I have an Archer C2 that I use as wifi access point.

Connected as following :

 

- VOO modem in the garage (192.168.0.1) LAN port 1 -> network switch cisco 24 ports -> different plugs of the house including a printer (ip 192.168.0.x), some desktop pc, nintendo switch, wii-U console, etc...

                                port 2 -> Internet port of the Archer C2 in the living room. Generates a wireless network (192.168.1.0)

The modem has DHCP from 192.168.0.100 to 199.

 

my problem : when I use it like this, I cannot print documents from laptops connected to the wifi because the printer is not on the same network.

 

solution tried : instead of pluging the C2 to the internet port, I use one of the LAN plug and on the C2 configuration web interface, set the LAN IP adress to 192.168.0.2, disable dhcp (to use only 1 the dhcp server of the main modem).  Like this, my wifi items receive 192.168.0.xxx adress and I can use the printer, but in this case, internet is not very stable (a lot worst comparing with when I connect the C2 to the internet port).  I lose and recover internet from time to time and I am not satisfied with this solution.

 

My question : when I have my wifi network on 192.168.1.xxx, is there an option on the archer C2 that allows wifi equipment to have access to my printer (192.168.0.x) ?

 

I am not an IT network specialist as you can understand...

 

Thanks in advance for your support

 

Christophe

  2      
 
  2      
 
#1
Options
1 Accepted Solution
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)-Solution
2020-03-03 10:11:35 - last edited 2020-03-04 05:41:29

@Kevin_Z 

 

Hi, 

 

Finally, I have plugged the Archer on the WAN port (so wifi on 192.168.1.x).  The printer as been set to fix ip and this adress is given to DMZ.  The printer as been installed on every pc and it works fine !

 

Thanks again for your support :-)

 

Christophe

Recommended Solution
  0  
  0  
#5
Options
5 Reply
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
2020-03-02 08:55:16

@tofgauthier 

 

Hello Christophe, due to the double NAT issue ( different IP subnet), the devices connected to the Archer C2 cannot access the printer which connects to the switch; like you mentioned, you can switch the Archer C2 as access point ( No DHCP server, the same subnet LAN IP), all the devices can access each other. 

 

If you want to use the Archer C2 as the regular router and access the printer, you can enable DMZ for your PC which connects to the Archer C2, and then add the printer into your PC under printer page. Then you can try to print and verify whether it works. 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
2020-03-02 11:35:35

Hi, 

 

Thanks for your reply.  I forgot to mention something.  I have another small access point connected to my main network (192.168.0.x), a tp link nano router.

So I have 2 different SSID on the same network.  Could this cause my stability problems ?

 

Regards, 

 

Christophe

  0  
  0  
#3
Options
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
2020-03-03 02:04:01

@tofgauthier 

 

Hello Christophe, thanks for your reply. 

 

The wireless interference will affect the performance. You can unplug the nano router and use Archer C2 only as the regular access point to give it a go. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)-Solution
2020-03-03 10:11:35 - last edited 2020-03-04 05:41:29

@Kevin_Z 

 

Hi, 

 

Finally, I have plugged the Archer on the WAN port (so wifi on 192.168.1.x).  The printer as been set to fix ip and this adress is given to DMZ.  The printer as been installed on every pc and it works fine !

 

Thanks again for your support :-)

 

Christophe

Recommended Solution
  0  
  0  
#5
Options
Re:giving access to my wifi network (192.168.1.XXX) to my wired network (192.168.0.XXX)
2020-03-04 05:41:24

@tofgauthier 

 

Glad to hear that it works well right now. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 2

Views: 3004

Replies: 5

Related Articles
 Deco M9 Plus app no longer allows DHCP Interval 192.168.1.xxx
276 3
TL-MR6400 wifi not giving IP address
771 0
 TD-W8968 wifi modem not giving
654 0
My router doesn't have WPS button and my Extender isn't giving any internet access
1565 0
Network security
541 0
 Help. Router giving 30mg plugs giving 3mg
445 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.