Home Network Community > Adapters > Switch to SoftAP mode
< Adapters

Switch to SoftAP mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Switch to SoftAP mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Switch to SoftAP mode
Switch to SoftAP mode
2020-03-04 16:08:40 - last edited 2020-03-05 03:45:29
Model: Adapter  
Hardware Version: V1
Firmware Version:

I have an Archer T2U AC600 USB key which worked very well under windows 7. I used the SoftAP mode as an access point to control certain PC software with my ipad and iphone and of course wireless. I just exceeded my PC under windows 10 and I no longer have access to the softAP mode which remains grayed out. Anyone has this problem?

  0      
 
  0      
 
#1
Options
4 Reply
Re:Switch to SoftAP mode
2020-03-05 03:45:03 - last edited 2020-03-05 03:45:29

@reidid789 

 

Hello, the Windows 10 does not support SoftAP mode, instead, you can use the built-in mobile hotspot to satisfy your needs. 

 

Below is the instruction to configure it: 

https://www.tp-link.com/support/faq/2021/

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Switch to SoftAP mode
2020-03-05 21:04:56

Good evening Kevin_Z

Thank you for your answer
It's not enough.
I explain again my problem: I use the TouchOSC software which allows you to drive in both directions a Windows 10 PC software and an ipad and / or an iphone ... Under W7 the SoftAP mode of my AC600 key allowed me to create a local wireless link between my different PC, ipad and iphone devices. Under W10 I understood that the SoftAP mode was no longer managed but there must be a way to receive this "small local network" to discuss these three devices over Wifi ??? !!!  I'm not talking about sharing an internet connection or a public wifi network

  0  
  0  
#3
Options
Re:Switch to SoftAP mode
2020-03-06 20:50:57

To use the functionality of TouchOSC https://hexler.net/products/touchosc I need to connect a W10 PC to Wifi using an iPad. It was simple with a W7 PC with SoftAP mode. But now that my PC is in W10 it no longer supports SoftAP mode, how do I do with my Archer AC600 key?
I am reformulating but am I the only one having this problem?

  0  
  0  
#4
Options
Re:Switch to SoftAP mode
2020-03-09 19:58:11

Good evening,
I found thanks to this tutorial and I will share it with you:
https://www.presse-citron.net/tuto-mardi-creer-point-dacces-wifi-pc-windows-10/

It works perfectly and I get this as a network : see IMG7569

The only problem now is to save this network configuration. Because when the PC reboots the studiodid network disappears and you have to launch it again. It's annoying!
Can someone help me ...

File:
IMG_7569.JPGDownload
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 3542

Replies: 4

Related Articles
 I can´t to set ON softAP mode
1723 0
 Bad performance in SoftAP mode
631 0
 TL-WN823N SoftAP mode
1118 0
 Change channel in SoftAP mode
623 0
 Unable to enable SoftAP mode...
1298 0
 Can't turn On SoftAP mode
3879 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.