Home Network Community > Deco > Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
< Deco

Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-19 18:03:56
Model: Deco M5  
Hardware Version: V1
Firmware Version: 1.4.4

Ran the latest update but it only updates 2 of 5 Deco's. See attached file.

 

The other 3 remain on 1.4.2

 

Please advise

File:
Deco 1.4.4.PNGDownload
  2      
 
  2      
 
#1
Options
7 Reply
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-20 02:10:00

@Kingdaveontour1 

 

Hello, try to connect these Decos to the main Deco directly by wired cable and update the firmware. 

 

If it still does not work, you can connect the slave Deco to the main Deco one by one to give it a shot. 

 

Any updates, be free to let us know. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-20 08:47:05

@Kevin_Z Hi

 

Not even the main deco has updated. Just 2 slaves..

 

Should i still try this?

 

I did disconnect the 2 discs at 1.4.4 and ran the update again on the remaining ones but it says that 1.4.2 is the latest update..

  0  
  0  
#3
Options
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-20 09:40:01

@Kingdaveontour1 

 

Thanks for your information. May I know what are the country versions of the three 1.4.2 Decos? You can find them on the back label of the actual device, next to the model number. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-20 10:34:35

@Kevin_Z Thanks

 

All 5 are FCC ID TE7M5

 

Is that the code you need?

  0  
  0  
#5
Options
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-03-22 03:00:57

@Kevin_Z just wanted to add that i'm seeing the same thing on my units.

 

I'm running the fixed 1.4.2 version on all my Decos and received a notification of a firmware update, but the update is only showing up for 3 of my 4 Decos.  I do have two versions of Deco M5 units: 3 of them are CA 2.0 and one is US 2.1.  I was going to try downloading the firmware and updating the one unit individually, but I cannot find the download for 1.4.4 65392.

  1  
  1  
#6
Options
Re:Firnware 1.4.4 only updates on 2 of 5 decos - othewrs remain on 1.4.2
2020-04-01 12:38:25

@Kingdaveontour1 All rolled out now and on the latest firmware..

  0  
  0  
#7
Options
After updated firmware 1.4.4 AP mode failed
2020-05-21 16:42:23

hello TP Link,

today i just bought the Deco M5.

once completed the setup with my unifi router using AP Mode, it runs perfectly fast.

unfortunately after the apps prompted me to update the firmware and updated, the AP Mode failed. 

 

please help,

  0  
  0  
#8
Options

Information

Helpful: 2

Views: 1973

Replies: 7

Related Articles
 Connect 2 decos to ethernet
318 0
Is my set up correct? All decos are wired directly to wall cat 5
547 0
 1.4.4 Firmware EU V2.2
595 0
 Issues since update to firmware 1.4.4
916 1
Deco M5 1.4.4 Guest Network
1169 0
 M5 Deco firmware update 1.4.4 should I bother?
873 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.