DLNA Blocker with AX50 in Access Mode
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I got an AX50 and installed it in Access Mode with a variety of cable connection running through it. It replaced a D-link router that had been doing the same thing for years. The first thing that I noticed is that a DLNA server I have attached to it with a wire was not showing up on the network. There does not seem to be any settings in access mode that block or allow traffic. I "assumed" it should just act as an open switch.
Any ideas?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I forgot to reply. Installing the newest firmware solved the issue for me. 1.0.9 Build 20200708 rel.55037(5553)
I had to hunt to find the firmware as it does not show up on the Canada support site.
- Copy Link
- Report Inappropriate Content
@Red90 Thx for your reply.
I do have the latest firmware installed, but the DLNA-communication between TV and NAS does still not work via the AX50 while in AP-mode.
It only works in router-mode with disabled "IGMP-snooping" and "IGMP Proxy" in the IPTV-settings.
Switching then back to AP-mode does not work, i have to stay in router mode @Kevin_Z.
@TP-Link, please fix this.
- Copy Link
- Report Inappropriate Content
Have you tried my previous suggestions that by switching the AX50 to router mode then disable the IGMP snooping and IGMP proxy, then switch it back to AP mode and confirm again?
Or, you are suggested to reset the AX50 to factory defaults by holding the reset button until the LEDs flashes off then on, then reconfigure it from scratch, follow the above steps to check again, thanks.
- Copy Link
- Report Inappropriate Content
Hi
I have the same problem. I have firmware 1.0.9 Build 20200708 rel.55037. I must connect my Qnap directly to main router Huwaei - then by cable from Huwaei to AP AX50 - and AX50 to my TV and DLNA is working. Qnap assistant check my disc server and it was OK. Problem is with router AX50
- Copy Link
- Report Inappropriate Content
Have you tried the suggestions provided by Alexander_S?
"Either I connect my TV to the router and mind going through the AX50, or I leave the AX50 in router-mode and deactivate "IGMP-snooping" AND "IGMP Proxy" in the IPTV-configs."
- Copy Link
- Report Inappropriate Content
@Kevin_Z Ok I back to router ( turn off access point ) turn off ""IGMP-snooping" AND "IGMP Proxy" in the IPTV-configs" and back to access point. Still the same problem.
- Copy Link
- Report Inappropriate Content
@Red90 Also I have main router Huwaei HS8145V ( fiber internet ) from on of this ports I have link by cable AX50. Main router IP is 192.168.100.1 and DHCP and Wi Fi is on. On my AX50 I can't set to router mode ( i try LAN 192.168.0.1 and IP Static 192.168.100.5 ). This AX50 only works on AP
- Copy Link
- Report Inappropriate Content
Hi, thanks for getting back, we will have to have more details about the issue you are experiencing, then we will check and see if there is a solution.
1. Please provide the detailed network layout/diagram, how is the AX50 connected to the Huawei HS8145V? Is the AX50' WAN to Huawei HS8145V' LAN, or LAN to LAN? You can also try to reconfigure the AX50 into an access point as per this instruction: https://www.tp-link.com/support/faq/417/.
2. Is this Qnap connected to the AX50 LAN or Wi-Fi? What is the IP address on it?
3. How did you test the DLNA server is not working? Are you unable to find the Qnap from Xbox? Are you able to find it on some Windows computer?
- Copy Link
- Report Inappropriate Content
1. Please provide the detailed network layout/diagram, how is the AX50 connected to the Huawei HS8145V? Is the AX50' WAN to Huawei HS8145V' LAN, or LAN to LAN? You can also try to reconfigure the AX50 into an access point as per this instruction: https://www.tp-link.com/support/faq/417/.
I have Lan to Lan by Ethernet cable. Main router is 192.168.100.1. Yes AX50 is working as AP on adres 192.168.100.2 but it loosing all futures. I want have two routers in my house, no one router and AP
2. Is this Qnap connected to the AX50 LAN or Wi-Fi? What is the IP address on it?
Qnap is connected by cable so LAN to LAN. His adres is static IP 192.168.100.43
3. How did you test the DLNA server is not working? Are you unable to find the Qnap from Xbox? Are you able to find it on some Windows computer?
DLNA doesn't work on TV, XBOX and Windows 10. When I connect Qnap to Huwaei router all is working fine. On AX50 DLNA doesn't exist
- Copy Link
- Report Inappropriate Content
Thank you very much for getting back with all the details. What if you change the AX50 to router mode, and connect the Huawei HS8145V'LAN to the AX50's WAN, then connect the Qnap and the TV/XBOX/Windows 10 to the AX50, either on LAN or on Wi-Fi, ensure they all obtain the IP address from the AX50 automatically, check if they can communicate.
Switch off the "IGMP-snooping" AND "IGMP Proxy" as well.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 6519
Replies: 42
Voters 0
No one has voted for it yet.