How to block inbound connection from a specific IP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to block inbound connection from a specific IP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to block inbound connection from a specific IP
How to block inbound connection from a specific IP
2020-08-23 08:09:10 - last edited 2020-08-30 08:08:49
Model: Archer VR600  
Hardware Version: V2
Firmware Version: 0.2.0 0.9.1 v0074.0 Build 170504 Rel.68210n

Hello,

 

Could someone please help me in configuring my router to reject all incomming connections initiated by a host on the internet, by specifying it's source IP. Thanks a lot in advance 

  0      
  0      
#1
Options
1 Accepted Solution
Re:How to block inbound connection from a specific IP-Solution
2020-08-30 02:46:20 - last edited 2020-08-30 08:08:49

@guy_c 

Good Day.

Thank you very much for your kind reply.

I am really sorry that Archer VR600 does not support this feature yet.

If possible, you could try to use the VPN connection, such as OpenVPN, IPsec VPN to access the LAN server, instead of using the port forwarding.

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:How to block inbound connection from a specific IP
2020-08-25 08:07:37

@guy_c 

Good day.

Thank you very much for your time and patience.

Are you trying to block a specific public IP address from accessing the router’s internal network?

May I know why do you want to do that?

Normally, if you did not enable the remote management on the modem or open any ports for the internal clients, all the WAN access would be blocked.

 

Thank you very much,

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:How to block inbound connection from a specific IP
2020-08-25 09:26:35

@Sunshine 

Thank you very much for your time. I have a server on port p. An offending host on the Internet is trying to enter the server and succeeds because it does a port scanning and eventually hits port p. Usually, such hosts are listed in the abuseipdb site because they run a software trying to make as much damage in a minimal time, for the fun. My server reports such attaks and i need to feed the offending IP so that inbound connections with this source IP are being blocked at the router's whatever the port.

 

Thanks again

 

 

  0  
  0  
#3
Options
Re:How to block inbound connection from a specific IP-Solution
2020-08-30 02:46:20 - last edited 2020-08-30 08:08:49

@guy_c 

Good Day.

Thank you very much for your kind reply.

I am really sorry that Archer VR600 does not support this feature yet.

If possible, you could try to use the VPN connection, such as OpenVPN, IPsec VPN to access the LAN server, instead of using the port forwarding.

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options