Home

Forums

Stories

Knowledge Base

Home Network Community > DSL Modem Routers > Archer vr400, can't upgrade from v2 to v3

< DSL Modem Routers

Archer vr400, can't upgrade from v2 to v3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer vr400, can't upgrade from v2 to v3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MABMED

2020-08-27 12:12:30 - last edited 2020-08-28 09:45:26

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-08-27

Archer vr400, can't upgrade from v2 to v3

2020-08-27 12:12:30 - last edited 2020-08-28 09:45:26

Model: Archer VR400

Hardware Version: V2

Firmware Version: V2_0.6.0_0.9.1

I tried to upgrade my router archer vr400 from firmware v3 to the new firmware v3 but it failed.

Got message: file not excepted.

Thank you.

1 Accepted Solution

Sunshine

2020-08-28 09:44:28 - last edited 2020-08-28 09:45:26

Posts: 7375

Helpful: 1195

Solutions: 915

Stories: 0

Registered: 2018-12-17

Re:Archer vr400, can't upgrade from v2 to v3-Solution

2020-08-28 09:44:28 - last edited 2020-08-28 09:45:26

@MABMED

Good day.

Did you try to update the firmware of V2 to V3?

If yes, it is not acceptable, you could only update from an older version of V3 to the latest version of V3, which means on the same hardware version.

While, if not from V2 to V3, but on the same hardware version, please check the following suggestions:

Make sure the firmware you used is bin file, not zip file;
What is your current firmware and what is the firmware you wish to update;

Thank you!

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.

Recommended Solution

1 Reply

Sunshine

2020-08-28 09:44:28 - last edited 2020-08-28 09:45:26

Posts: 7375

Helpful: 1195

Solutions: 915

Stories: 0

Registered: 2018-12-17

Re:Archer vr400, can't upgrade from v2 to v3-Solution

2020-08-28 09:44:28 - last edited 2020-08-28 09:45:26

@MABMED

Good day.

Did you try to update the firmware of V2 to V3?

If yes, it is not acceptable, you could only update from an older version of V3 to the latest version of V3, which means on the same hardware version.

While, if not from V2 to V3, but on the same hardware version, please check the following suggestions:

Make sure the firmware you used is bin file, not zip file;
What is your current firmware and what is the firmware you wish to update;

Thank you!

Archer vr400, can't upgrade from v2 to v3

Archer vr400, can't upgrade from v2 to v3

Information

Voters 0

Tags