Deco P7 1.4.7 Firmware Update disaster
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
This morning I updated my P7s to the new fw 1.4.7.
My internet Speed was 138MBit. Now I have up to 15MBit!!
In the past the decos we're connected over Ethernet. This is not working anymore!
In addition I didn't find any changes in the fw except it kills the Ethernet.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hello again @kiliclat and all, thank you all for the detailed info you've provided as for now and the issue is addressed already, we have removed the 1.4.7 version from the official website. We will soon fix and release a new firmware later.
As for those who encounter the same issue that the satellite Deco P7 nodes will disconnect from the main P7 (AP mode) after upgrading the firmware to this 1.4.7 Build 20200820 Rel. 60546 version, it is suggested to downgrade the firmware to the previous 1.4.2 version as a workaround, and below is the guidance:
https://www.tp-link.com/support/faq/1599/ (Method 2)
Thanks a lot and sorry for any inconvenience caused on this~
- Copy Link
- Report Inappropriate Content
@Lexivienna please take a look on my post this firmware have a real problem
- Copy Link
- Report Inappropriate Content
thx. I have the problems in router mode.
having the main deco between the modem and my master switch using both Ethernet ports as a pass through.
- Copy Link
- Report Inappropriate Content
@Dim17 i confirm we can donwgrade firmware:
i try this tutorial from deco to downgrade : https://www.tp-link.com/en/support/download/deco-p7/#Firmware
Step 1 Connect your device to the Deco network (wired or wirelessly).
Step 2 Launch a web browser, enter http://tplinkdeco.net or the LAN IP address shown on the Deco app in the address bar to access the web management page of the Deco.
donwload 1.4.2 firmware and use http://tplinkdeco.net to downgrade
everyrthing is fine now.
i need try 3 times before downgrade is ok
hope everything is fine for you too
i m now on 1.4.2
- Copy Link
- Report Inappropriate Content
@Lexivienna if you need help don t hesitate
- Copy Link
- Report Inappropriate Content
Same problems here!
Installed the update this morning, and only the main unit worked; every other connected unit had a pulsing red LED-light. My main unit is also connected in AP-mode.
I downgraded to 1.4.2 and everything works again. The other P7-units seem to have version 1.4.7 installed, but my main unit is now 1.4.2.
I will wait to upgrade the main unit until we have some feedback from TP-Link.
- Copy Link
- Report Inappropriate Content
Hey, firmware dev team? How long we will be beta testers? We reported an issue - no feedback. Maybe you just need to hide firmware for now from the site?
What a shame that you do not test your firmware. Such good hardware with so poor support. So many basic things are missing, so upset as a customer and for sure will never buy anything from this vendor.
- Copy Link
- Report Inappropriate Content
@lunatick84 Personnaly i prefered downgrade all units. For this i practised 3 times the downgrade.(pack 3 )
- Copy Link
- Report Inappropriate Content
Hello again, thanks a lot for reporting this issue to the community.
We will soon look into this issue and update it.
- Copy Link
- Report Inappropriate Content
@Lexivienna Thanks for the heads up. I was already exciting assuming most of my problems would go away with this fw update but I came to the communities before clicking on the update button. @TP_LINK @TP-link_de , if this fw have such problems, it would really make sense having it removed from the downloads area
thanks
- Copy Link
- Report Inappropriate Content
Hello, we are checking this issue with the highest priority now and will take the next step if there is a necessity to remove it, thanks a lot for your suggestions again.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 4631
Replies: 23
Voters 1
