Home Network Community > Wi-Fi Routers > No APs visible when surveying for WDS 5ghz in C50
< Wi-Fi Routers

No APs visible when surveying for WDS 5ghz in C50

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

No APs visible when surveying for WDS 5ghz in C50

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
No APs visible when surveying for WDS 5ghz in C50
No APs visible when surveying for WDS 5ghz in C50
2020-09-14 12:53:10 - last edited 2020-09-18 07:57:33
Model: Archer C50  
Hardware Version: V4
Firmware Version: idk

I wanted to use my router as an extender for my Huawei GPON. When I tried to use WDS for 2.4 band, it shows all the APs - of my network as well as my neighbour's.

 

However, when I tried to do the same for 5ghz, no APs are visible. From other forums I even changed the channel width of the Huawei Router to 40MHz, however that didnt work.

 

 

File:
  0      
 
  0      
 
#1
Options
3 Reply
Re:No APs visible when surveying for WDS 5ghz in C50
2020-09-16 09:40:07 - last edited 2020-09-18 07:57:33

@patreiek 

 

Hello, try to change the 5GHz wireless channel to 36/40/44 to give it a go on your Huawei GPON, then reboot the Huawei GPON as well as the C50.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:No APs visible when surveying for WDS 5ghz in C50
2020-09-18 07:57:24
I dont see channel option for 36/44 but I do have it for 20/40/80; I tried it with 40 but no luck!
  0  
  0  
#3
Options
Re:No APs visible when surveying for WDS 5ghz in C50
2020-09-18 11:15:18

@patreiek 

 

Hello,

 

20/40/80MHz should be the channel width, it is not the channel option. Is it possible to seek some suggestions from Huawei GPON?

 

Thanks.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 425

Replies: 3

Related Articles
Where is WDS Bridging on Archer C50?
1130 0
Archer C50 5ghz problem
1197 3
Archer C50 5Ghz Wifi Slow
1410 0
Archer C50 5Ghz network not showing
2180 0
Archer C50 V4 unable to enable WDS feature
1234 0
 Archer C50 V6 WDS
694 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.