Home Network Community > Wi-Fi Routers > TL-WR902AC can communicate with the other subnet, but the other can't
< Wi-Fi Routers

TL-WR902AC can communicate with the other subnet, but the other can't

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-WR902AC can communicate with the other subnet, but the other can't

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-WR902AC can communicate with the other subnet, but the other can't
TL-WR902AC can communicate with the other subnet, but the other can't
2021-03-28 20:28:25 - last edited 2021-03-29 01:24:08
Model: TL-WR902AC  
Hardware Version: V3
Firmware Version: 0.9.1 0.3 v0089.0 191018

Hello,

installed the new travel router, set up router mode, set up static ip and found out that I can reach out the devices on the other subnet(192.168.1.0) with the devices connected on the wireless network(192.168.3.0) but, on the other hand, the same thing cannot be done if I try to reach from 192.168.1.0 to 192.168.3.0.

the 920AC can be detected by Advanced Ip Scanner, but doesn't respond to ICMP on cmd.

Tried to do some static routing on the main router but didn't work(as below):

Someone knows how to solve?

Thanks in advance.

  0      
 
  0      
 
#1
Options
3 Reply
Re:TL-WR902AC can communicate with the other subnet, but the other can't
2021-03-29 06:51:56

@Steven_Ji 

 

May I know the network layout? Is this 192.168.1.0 the WAN subnet of the WR902AC? If you want to access the WR902AC LAN from WAN, you need to open the corresponding ports for the specific IP address on the WR902AC network to allow that. You can refer to this guide to open the ports:

https://www.tp-link.com/support/faq/1379/

If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:TL-WR902AC can communicate with the other subnet, but the other can't
2021-04-01 17:41:43 - last edited 2021-04-01 17:41:57

Thank you fo replying. Yes, the 192.168.1.0 is the WAN of the nano router. Can I somehow open all ports for all the devices on 192.168.3.0 without opening them one at a time?

  0  
  0  
#3
Options
Re:TL-WR902AC can communicate with the other subnet, but the other can't
2021-04-01 18:00:11 - last edited 2021-04-01 18:30:45

Update:

After hours of looking around I found "SPI firewall" in "Security" and "basic security" section, disabling it allowed me to lower the firewall and allow all packets on all ports toward all devices(except for the 192.168.3.1, why?).

 

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 434

Replies: 3

Related Articles
USB 4G for TL-WR902AC
8062 0
TL-WR902AC - no internet connection?
2623 0
TL-WR902ac extender mode
592 0
Restoring Stock firmware on TL-WR902AC
5369 0
TL-WR902AC WPA Enterprise as Client
1531 1
TL-WR902AC Nano Router in Client Mode
577 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.