Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Archer C20 auto reconnect problem

< Wi-Fi Routers

Archer C20 auto reconnect problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C20 auto reconnect problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

aguero9320

2021-07-15 07:32:05

Posts: 1

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2021-07-15

Archer C20 auto reconnect problem

2021-07-15 07:32:05

Model: Archer C20

Hardware Version: V5

Firmware Version: 0.9.1 4.17 v0001.0

I have an Archer C20 v5 US version. When internet gets disconnected because of ISP and when internet comes back, a lot of the times the Router doesnt get automatically connected back to the internet. The "Status" would show assigned IP address but the all clients still show "no internet access". Only manually pressing "connect" in the "network page" or rebooting the router works. I've already set connection to be active at all times and set idle time as 0. The problem still happens.

3 Reply

Kevin_Z

2021-07-16 07:48:10

Posts: 21587

Helpful: 5042

Solutions: 2543

Stories: 21

Registered: 2018-12-24

Re:Archer C20 auto reconnect problem

2021-07-16 07:48:10

@aguero9320

Can we confirm who is your ISP, and is the WAN connection type on the C20, Dynamic IP?

If the router doesn't connect to the internet automatically after the modem restores, but there is still a WAN IP address and gateway, please try to change the DNS server on the C20 to 8.8.8.8 and 8.8.4.4 under Advanced > Network > Internet, where you can find "Use the following DNS addresses", then monitor again.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Jamajo56

LV1

2021-12-01 23:33:51

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-12-01

Re:Archer C20 auto reconnect problem

2021-12-01 23:33:51

I have exactly the same problem with my Archer C2300. It would ocassioanaly drop connection and would not reconnect unless manually rebooted.

Talked to the customer support and changed primary and secondary DNS to 8.8.8.8 and 8.8.4.4. I lost my connection again in 10 days.

I need a reliable router for my security system. It is really frustrating when I am ouside of my house and I am ubable to reach my home network remotely.

Kevin_Z

2021-12-02 07:44:17

Posts: 21587

Helpful: 5042

Solutions: 2543

Stories: 21

Registered: 2018-12-24

Re:Archer C20 auto reconnect problem

2021-12-02 07:44:17

@Jamajo56

Who is your ISP, and is the WAN connection type on the C2300, Dynamic IP? Is there still a WAN IP address when the internet is not available on the C2300? Please show us the screenshot of the status page when the internet is not available and when it is available after the reboot.

Try with a different cat 5e or cat 6 cable between the modem and the C2300.

BTW, when did you purchase the router, and when did the issue start to happen?

Archer C20 auto reconnect problem

Archer C20 auto reconnect problem

Information

Voters 0

Tags