Home Network Community > Wi-Fi Routers > 5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
< Wi-Fi Routers

5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
2021-11-28 10:22:40 - last edited 2022-02-18 06:44:35
Model: Archer C6  
Hardware Version: V2
Firmware Version: 1.3.6 Build 20200902 rel.65591(4555)
I have set the 5GHz bands channel width to 40MHz so that i get better bandwidth in my bedroom. On 80Mhz channel I get just 35mbps bandwidth in my bedroom.
 
Every time i reboot(or switch off and switch on) the router, the channel width on 5GHz band gets reset to 80MHz( I checked on WiFi analyzer app on Android and the link speed also increased from 185mbps to 375mbps) but in the router Management page it shows that my channel width is 40MHz which is wrong.
 
This is issue is also triggered when I disable and then re-enable the Wireless 5Ghz transmission(from Router managment web page), the channel width will reset from 40MHz/20MHz to 80MHz but in Router management page in the selection box it will still show 40Mhz as channel width.
 
Please fix this.
  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.-Solution
2022-02-16 08:58:54 - last edited 2022-02-18 06:44:35

FlatPepsi wrote

@Kevin_Z  5GHz band: On Auto mode, the channel width is always set to 80Mhz . Mode: 802.11a/n/ac mixed I want to set the channel width to 40Mhz because on 80Mhz the coverage in my bedroom is not good. Tested on Mobile phone and laptop. When i set the channel width to 40Hz and restart the router/ Power On-Off/Disable the 5Ghz radio by unchecking the selection box, the routers channel width is set to 80MHz(checked on 3 mobile phones/Laptop) but on the Router management web page the settings value will display 40MHz.

 

Thank you for getting back @FlatPepsi.

 

Can you please try installing the beta firmware we provided here, then monitor again? I believe your router is an EU version, so you can try the beta firmware we provided there.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#6
Options
5 Reply
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
2021-11-29 06:47:48

@FlatPepsi 

 

Hello, will the speed and bandwidth differ a lot when the 5GHz channel width is on Auto, 80MHz or 40MHz? Can we have more details? Except for the channel width is different, are there any other changes you can be aware of when the speed changes? What if you just leave the channel width Auto, is the 5GHz speed not good?

 

What is the device you are testing for the 5GHz speed? You can also try with another device by connecting to the 5GHz network to see if that also happens the same.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
2022-02-15 13:36:34

  @Kevin_Z I had the same issue earlier, see here: Archer C6 v2 Wi-Fi 5 GHz channel width issue - Home Network Community (tp-link.com)

However this seems to work now properly with the latest beta firmware. BTW is it planned to release that firmware as non-beta any time?

  0  
  0  
#3
Options
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
2022-02-15 17:52:44 - last edited 2022-02-15 17:54:20

@Kevin_Z  5GHz band: On Auto mode, the channel width is always set to 80Mhz . Mode: 802.11a/n/ac mixed I want to set the channel width to 40Mhz because on 80Mhz the coverage in my bedroom is not good. Tested on Mobile phone and laptop. When i set the channel width to 40Hz and restart the router/ Power On-Off/Disable the 5Ghz radio by unchecking the selection box, the routers channel width is set to 80MHz(checked on 3 mobile phones/Laptop) but on the Router management web page the settings value will display 40MHz.

  0  
  0  
#4
Options
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.
2022-02-16 08:53:05 - last edited 2022-02-16 08:55:38

BPeter wrote

  @Kevin_Z I had the same issue earlier, see here: Archer C6 v2 Wi-Fi 5 GHz channel width issue - Home Network Community (tp-link.com)

However this seems to work now properly with the latest beta firmware. BTW is it planned to release that firmware as non-beta any time?

 

Hello @BPeter, thank you very much for reminding me of your post which I haven't been aware of, sorry for that. But it's glad to hear that the issue was resolved by installing beta firmware on the router. Can I confirm which beta firmware did you install? Is it the one we provided here? 

https://community.tp-link.com/en/home/forum/topic/271574

 

As confirmed with the development team, there is a plan to release an official version for Archer C6(EU) 2.0 in the future, but we cannot provide you an ETA now, so please keep an eye on the router web GUI or Tether app for the updates. We will also update the above thread to inform you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:5GHz band channel width of Archer C6 V2 EU gets set to 80MHz on router restart.-Solution
2022-02-16 08:58:54 - last edited 2022-02-18 06:44:35

FlatPepsi wrote

@Kevin_Z  5GHz band: On Auto mode, the channel width is always set to 80Mhz . Mode: 802.11a/n/ac mixed I want to set the channel width to 40Mhz because on 80Mhz the coverage in my bedroom is not good. Tested on Mobile phone and laptop. When i set the channel width to 40Hz and restart the router/ Power On-Off/Disable the 5Ghz radio by unchecking the selection box, the routers channel width is set to 80MHz(checked on 3 mobile phones/Laptop) but on the Router management web page the settings value will display 40MHz.

 

Thank you for getting back @FlatPepsi.

 

Can you please try installing the beta firmware we provided here, then monitor again? I believe your router is an EU version, so you can try the beta firmware we provided there.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 865

Replies: 5

Related Articles
Archer C6 v2 Wi-Fi 5 GHz channel width issue
1078 0
 Unable to limit band width for my Archer C6
4610 4
 Unable to limit band width for my Archer ‏c6.v3.20
746 0
Archer C6 v2: 5Ghz WDS Bridging Setup Grayed!
3630 0
Switching 160Mhz 5GHz Channel Width in Archer AX72 Router
528 0
Archer C6 switch off hidden channel
1463 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.