Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Archer A6 become brick after firmware upgrade

< Wi-Fi Routers

Archer A6 become brick after firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer A6 become brick after firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer A6 become brick after firmware upgrade

2022-03-17 15:06:47 - last edited 2022-04-06 09:33:09

Posts: 4

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2022-03-17

Archer A6 become brick after firmware upgrade

2022-03-17 15:06:47 - last edited 2022-04-06 09:33:09

Model: Archer A6

Hardware Version: V3

Firmware Version: Not sure

Hello

After firmware upgrade today through Tether App in mobile Archer A6 has become brick and not working. All lights are ON but not able to connect to internet. In Tether app, it shows 'offline' status and also i am not able to restart router too. I am not sure what to do.

Please help me to restart my router or do firmware upgrade, etc. It has to work and without internet it becomes very difficult to work at home and take some online classes.

Thanks and Regards

Anjali

0

0

#1

1 Accepted Solution

LV7

2022-03-17 17:43:41 - last edited 2022-04-06 09:33:09

Posts: 7030

Helpful: 5235

Solutions: 1162

Stories: 7

Registered: 2013-10-12

Re:Archer A6 become brick after firmware upgrade-Solution

2022-03-17 17:43:41 - last edited 2022-04-06 09:33:09

Try to reset the router to its factory defaults like this:

If the router starts normally go ahead and re-configure from scratch.

If the issue persists contact your local support for assistance.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

Recommended Solution

0

0

#2

3 Reply

LV7

2022-03-17 17:43:41 - last edited 2022-04-06 09:33:09

Posts: 7030

Helpful: 5235

Solutions: 1162

Stories: 7

Registered: 2013-10-12

Re:Archer A6 become brick after firmware upgrade-Solution

2022-03-17 17:43:41 - last edited 2022-04-06 09:33:09

Try to reset the router to its factory defaults like this:

If the router starts normally go ahead and re-configure from scratch.

If the issue persists contact your local support for assistance.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

Recommended Solution

0

0

#2

LV1

2022-03-20 03:28:09

Posts: 4

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2022-03-17

Re:Archer A6 become brick after firmware upgrade

2022-03-20 03:28:09

Reset is also not working.

And support is also not answering Or working.

0

0

#3

2022-04-06 09:32:37

Posts: 21605

Helpful: 5052

Solutions: 2546

Stories: 21

Registered: 2018-12-24

Re:Archer A6 become brick after firmware upgrade

2022-04-06 09:32:37

If the router is determined to be faulty, you can contact the local support via email to be advised further:

https://www.tp-link.com/support/contact-technical-support/#E-mail-Support

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

0

0

#4