Vr600 V2 upstream errors

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Vr600 V2 upstream errors

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Vr600 V2 upstream errors
Vr600 V2 upstream errors
2022-10-20 03:31:26 - last edited 2022-10-20 03:34:11
Model: Archer VR600v  
Hardware Version: V2
Firmware Version: 0.2.0 0.9.1 v0074.0 Build 170504 Rel.68210n

I recently replaced my Sky SR203 hub with a second-hand TP-Link Archer V600 V2 router. The switch over was painless. From what I can see, the Internet has been stable and there's been no loss of connection as of yet. 2 days 2 hours is the up time as of this post. 

 

I have noticed, however, that there's quite a bit of errors on the upstream connection. It's reported 532 errors so far in the 2 days 2 hours up time. Is this something to be concerned about? There's no errors on the downstream yet. 

  0      
  0      
#1
Options
4 Reply
Re:Vr600 V2 upstream errors
2022-10-21 11:08:19

  @ALL_SYS_PWRGD 

I think if the internet is fine, there is no need to change any settings otherwise it might make things worse.

But if you are interested, you could try to enable SRA under Advanced>Network settings>DSL settings.

  0  
  0  
#2
Options
Re:Vr600 V2 upstream errors
2022-10-21 17:37:43 - last edited 2022-10-21 17:38:42

The router did appear to have an issue yesterday. All of a sudden, the Internet cut out. I logged into the router to see what went wrong. It was telling me to configure the DNS manually.

 

 

I rebooted and it reconnected. However I noticed that the speed was at 79999/20000 which has never happened before and the SNR margin dropped from the usual 3.4dB to -0.5dB. This did not last. It quickly resynced at the speed I usually get with the correct SNR margin.

 

 

The downstream accumulated 935 errors not too long after resync. These have now stopped. Upstream is just slowly accumulating errors. I'd say it rises by around 10-15 an hour. Not sure if this is a sign of a faulty router. It's not looking good that's for sure. Hopefully I don't have any further issues.

  0  
  0  
#3
Options
Re:Vr600 V2 upstream errors
2022-10-24 01:00:44

  @ALL_SYS_PWRGD 

 

I think the router is faulty. I have noticed that when I do a speed test and it jumps to the upload test, I get insane ping spikes (we're talking anywhere from 200-3000ms ping). The spikes can be seen on speedtest.net and also when pinging something like 8.8.8.8 via CMD while running the upload test. 

 

The spikes occur on Ethernet and Wi-Fi on both a laptop and desktop PC. Download is OK. It spikes a little (due to bufferbloat), but it doesn't really go above 40-50ms ping. It's the upload test that causes massive spikes.

 

I went back to the SR203 hub, re-ran the test and the spikes returned to where I expect (between 20-40ms ping). That's a big difference and tells me the issue is the router.

 

Is there anything that can be done to resolve those spikes? Or is it a bad router? It's a shame because I liked the router. The Sky Hub is too basic.

  0  
  0  
#4
Options
Re:Vr600 V2 upstream errors
2022-10-24 05:34:19

Decided to upgrade firmware to see if it'd help. It did not. There's still insane ping spikes/packet loss when an upload speed test is run. I don't know what would cause this. The spikes aren't this bad when a download test is run. 

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 366

Replies: 4

Related Articles