Red Light/ blinking
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco s7 Red Lights
Hi recently Ive bought 2 Deco s7s and the LEDs are red
It shows up in the middle of the day no disconnect nothing it just shows up
->the main unit is solid red and the 2nd unit is blinking red.
I have already checked the logs for any errors but there doesn't seem to be any
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@SamsungHandy welcome to the community.
Just to double check when Deco S7 is red, you could still get internet service from Deco, right?
If it is just the LED issue, do you have another DNS server, such as the Ads filter Pi-Hole server in the network? or any access control settings on the ISP router?
The LED status indicates the network online detection result from Deco. If the DNS requests were resolved properly, the LED status will turn green/white.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP the network works just fine
I have an fritz box router where I turned off the wifi
On my phone I have set an private DNS server
From nextdns
What do you mean with access control on my router?
- Copy Link
- Report Inappropriate Content
"What do you mean with access control on my router?"
Some settings like allowing/blocking certain websites/devices.
If the private DNS server is used for the smartphone only, it would not affect the network behavior of Deco.
Since there is a fritz box router already, have you tried to set up Deco S7 into Access Point mode to see whether Deco would still randomly turn red?
How to set up Deco to work in Access Point mode
Best regards.
- Copy Link
- Report Inappropriate Content
The Fritz Box is pretty stock besides some open ports UDP/TCP
So no blocking websites
I will try access point mode thx
- Copy Link
- Report Inappropriate Content
Hi @David-TP,
So today as I woke up the Deco at the top floor(not the main) flashed red ->Internet still worked
The bottom one which is the main unit was white so everything good
Unfortunately I had no time to change to access point mode but I saw this with red light today
Can i paste in the logs from the decos in here? Would that help?
- Copy Link
- Report Inappropriate Content
@SamsungHandy and @David-TP
Can I ask if this was resolved in any fashion?
Mine is already setup in AP Mode.
Main unit is solid RED.
2 x slave units have flashing RED.
Also can I ask where you got the logs from the unit(s)?
Extra information:-
DNS is configured from router with 1.1.1.1 and 9.9.9.9.
Units are all connected to router via ethernet.
Access seems to be fine, but RED LED's persist
- Copy Link
- Report Inappropriate Content
Hi this was kinda resolved yes I have just set the LED to stay on 1min a day so it doesn't have a chance to blink red.
I don't know if that's the solution but it worked for me.
The logs I got from the Web Interface of the decos
Under Advanced->System->System Logs
Maybe try and open this iP in your browser it's the gateway for my decos
192.168.68.1
Maybe it's your DNS Settings try setting them in the Deco app
- Copy Link
- Report Inappropriate Content
@SamsungHandy
Thanks for the feedback.
I have managed to browse into the units and see the logs.
I do see this entry 22 DEBUG 0days, 00:00:21, [smarthome]tlcc_get_link_status:1! [1-disconnected 2-connected 4-reconnecting]
I think that means 1-disconnected but the internet connection through all units on all devices seems OK.
Same trick with setting LED's to be OFF most of time seems to work for me, but I think this is just masking the issue.
These are brand new units.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 1223
Replies: 8
Voters 1
