Home Network Community > Powerline Adapters > Cannot Access Wifi on Extender
< Powerline Adapters

Cannot Access Wifi on Extender

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Cannot Access Wifi on Extender

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Cannot Access Wifi on Extender
Cannot Access Wifi on Extender
2023-04-25 17:29:08 - last edited 2023-04-26 06:02:59
Model: TL-WPA7617 KIT  
Hardware Version:
Firmware Version:

Hi,

trying to set up wifi on extender. SP Router doesn't have WPA, entered the router password on Extender to allow access for wireless devices but doesn't recognise it or the original password on the extender. Have tried resetting using button on the side but no success.

Can't access the device from the TP-Link App either

Help... How can I reset to factory settings and retry?

Cheers

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:Cannot Access Wifi on Extender-Solution
2023-04-26 06:02:53 - last edited 2023-04-26 06:02:59

  @BillSt 

 

Hi, WPS button is only used to clone wireless settings from the router, it doesn't matter if your router doesn't have a WPS button.

 

To install the powerline adapter and extender, please pair them first via pair button: How to set up a new secure wireless network using Powerline ac Wi-Fi Kit by Pair button

Then connect the adapter to your router via Ethernet cable, you will be able to get internet access from the powerline extender. The default wireless name and password is printed on the label of the extender itself.

 

If you would like to customize the wireless settings of the extender, please refer to the following two instructions:

How to customize Powerline ac Extender's wireless settings via web-based management interface

How to customize wireless settings on tpPLC Utility

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
4 Reply
Re:Cannot Access Wifi on Extender
2023-04-25 18:30:32

  @BillSt 

 

Hi,

 

If the router doesn't support WPA, what does it support then?

 

The TL-WPA7617 KIT apparently supports WEP, WPA and WPA2, which should be sufficient.

 

Below is a screenshot from the page in the user manual that explains how to reset the devices to factory default settings.

 

  0  
  0  
#2
Options
Re:Cannot Access Wifi on Extender
2023-04-25 20:56:35

woozle wrote

  @BillSt 

 

Hi,

 

If the router doesn't support WPA, what does it support then?

 

The TL-WPA7617 KIT apparently supports WEP, WPA and WPA2, which should be sufficient.

 

Below is a screenshot from the page in the user manual that explains how to reset the devices to factory default settings.

 

  @woozle Thanks for replying, I meant WPS, will try this when I can.

  0  
  0  
#3
Options
Re:Cannot Access Wifi on Extender-Solution
2023-04-26 06:02:53 - last edited 2023-04-26 06:02:59

  @BillSt 

 

Hi, WPS button is only used to clone wireless settings from the router, it doesn't matter if your router doesn't have a WPS button.

 

To install the powerline adapter and extender, please pair them first via pair button: How to set up a new secure wireless network using Powerline ac Wi-Fi Kit by Pair button

Then connect the adapter to your router via Ethernet cable, you will be able to get internet access from the powerline extender. The default wireless name and password is printed on the label of the extender itself.

 

If you would like to customize the wireless settings of the extender, please refer to the following two instructions:

How to customize Powerline ac Extender's wireless settings via web-based management interface

How to customize wireless settings on tpPLC Utility

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
Re:Cannot Access Wifi on Extender
2023-04-29 10:28:22

  @BillSt Idiot confession, I misread wifi password on extender - saw a 5 as a 6.

However I still couldn't access settings, kept getting "password incorrect". Reset extender. Managed to update firmware and got access. 

Not brave enough to try and replicate existing router name and password yet.

Thanks for help all.

  0  
  0  
#5
Options

Information

Helpful: 1

Views: 583

Replies: 4

Related Articles
 Cannot longer access my Powerline Wifi extender
837 0
 Cannot connet with wifi extender
388 0
 Computer cannot access extender signal
295 0
 Extra Extender cannot connect with WiFi
438 0
My extender cannot be seen during activation
258 0
Cannot connect to extender network
540 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.