Tplink mr600 v2 OpenVPN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tplink mr600 v2 OpenVPN

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Tplink mr600 v2 OpenVPN
Tplink mr600 v2 OpenVPN
2023-09-30 20:22:29 - last edited 2024-01-02 01:54:21
Model: Archer MR600  
Hardware Version: V2
Firmware Version:

Hi,

I try to setup my tplink mr600 v2 to connect with OpenVPN I do the steps from tplink router I put dynamic dns but the problem is on app OpenVPN when I put the configuration file and press connect I wait about 1min and say a message time is out retry. I need to enable NAT port ? If yes how I do that ?

Also I open the configuration file with editor to check if have the dynamic dns right and is fine .

 

Note when I put the file on OpenVPN the app don't ask my to put anything password or smthng else all was automatic.

 

here is the log i receive:

 

⏎[Oct 2, 2023, 16:18:12] Connecting to [(X).tplinkdns. com]:1194 (109.x.x.x) via UDP
⏎[Oct 2, 2023, 16:18:21] Server poll timeout, trying next remote entry...
⏎[Oct 2, 2023, 16:18:21] EVENT: RECONNECTING ⏎[Oct 2, 2023, 16:18:21] EVENT: RESOLVE ⏎[Oct 2, 2023, 16:18:22] Contacting 109.x.x.x:1194 via UDP
⏎[Oct 2, 2023, 16:18:22] EVENT: WAIT ⏎[Oct 2, 2023, 16:18:22] WinCommandAgent: transmitting bypass route to 109.x.x.x
{
    "host" : "109.x.x.x",
    "ipv6" : false
}

⏎[Oct 2, 2023, 16:18:22] Connecting to [(X).tplinkdns. com]:1194 (109.x.x.x) via UDP
⏎[Oct 2, 2023, 16:18:31] Server poll timeout, trying next remote entry...
⏎[Oct 2, 2023, 16:18:31] EVENT: RECONNECTING ⏎[Oct 2, 2023, 16:18:31] EVENT: RESOLVE ⏎[Oct 2, 2023, 16:18:32] Contacting 109.x.x.x:1194 via UDP
⏎[Oct 2, 2023, 16:18:32] EVENT: WAIT ⏎[Oct 2, 2023, 16:18:32] WinCommandAgent: transmitting bypass route to 109.x.x.x
{
    "host" : "109.x.x.x",
    "ipv6" : false
}

⏎[Oct 2, 2023, 16:18:32] Connecting to [(X).tplinkdns. com]:1194 (109.x.x.x) via UDP
⏎[Oct 2, 2023, 16:18:35] EVENT: CONNECTION_TIMEOUT  BYTES_OUT : 756
 PACKETS_OUT : 54
 RESOLVE_ERROR : 3
 CONNECTION_TIMEOUT : 1
 N_RECONNECT : 8
⏎[Oct 2, 2023, 16:18:35] EVENT: DISCONNECTED ⏎

 

can help me?

  0      
  0      
#1
Options
1 Accepted Solution
Re:Tplink mr600 v2 OpenVPN-Solution
2024-01-02 01:54:17 - last edited 2024-01-02 01:54:21

  @theGODisCOMING 

 

Hi, IP Address: 10.63.X.X is a private address, it means your ISP is using CGNAT which causes the VPN Server not connected from external network.

In that case, you will need to contact your ISP to see if they could assign you a public IP address.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
4 Reply
Re:Tplink mr600 v2 OpenVPN
2023-10-09 09:27:03

  @theGODisCOMING 

 

Hi, please check the Internet IPv4 address on Advanced->Status->Internet part to see if it is a public IP address or not, if not, it means your ISP is using CGNAT which causes the VPN Server not connected from external network. In that case, you will need to contact your ISP to see if they could assign you a public IP address.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Tplink mr600 v2 OpenVPN
2023-12-29 22:41:18 - last edited 2023-12-29 22:46:09

  @Sunshine 

Hi

i have thet: 

WAN Interface Name: LTE

MAC Address:  78.X.X.X.X.

IP Address: 10.63.X.X

Primary DNS: 94.143.X.X

Secondary DNS:  94.143.X.X

 

i try evrything on setting Openvpn but i cant found solution also i try to nat a port but also nothing.

also i use the router only with data sim!

the ISP upgrade where can i find it the fille to upgrade?

 

 

  0  
  0  
#3
Options
Re:Tplink mr600 v2 OpenVPN-Solution
2024-01-02 01:54:17 - last edited 2024-01-02 01:54:21

  @theGODisCOMING 

 

Hi, IP Address: 10.63.X.X is a private address, it means your ISP is using CGNAT which causes the VPN Server not connected from external network.

In that case, you will need to contact your ISP to see if they could assign you a public IP address.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
Re:Tplink mr600 v2 OpenVPN
2024-01-02 09:17:56

  @Sunshine 

ok thank you!

  0  
  0  
#5
Options