Archer VR300 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR300 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR300 V2
Archer VR300 V2
2023-10-12 14:28:26 - last edited 2023-10-22 17:38:10
Model: Archer VR300  
Hardware Version: V2
Firmware Version: V1.2_210831

I am using Version V1.2_210831 Then the infrastructure of my Internet was upgraded and there were ripples, so I did not update the modem to V1.2_220407, then the interface slowed down and the tabs load slowly when navigating from the interface.

So I switched to V1.2_210831 again, this time the internet is connecting late, I don't know what to do when I restart the modem, I'm currently using V1.2_210831 as an update, I'm not updating it, if I update it, the interface slows down and I can't navigate between tabs.

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Archer VR300 V2-Solution
2023-10-22 09:49:51 - last edited 2023-10-22 17:38:17

  @Huseyin_19 

 

The latest official FW for your VR300 v1.2 is V1.2_220407.

What you can do is to make a configuration backup of your modem. Update to the latest official FW version - V1.2_220407

Reset the device to its factory defaults and then restore its configuration from the backup you've made earlier:

 

 

Then test if the device is working as expected. You may have to switch to another web browser (Firefox, Chrome) to exclude a potential web browser issues.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#3
Options
Re:Archer VR300 V2-Solution
2023-10-22 17:26:37 - last edited 2023-10-22 17:38:10

  @Huseyin_19 

 

TBH I saw a little delay when you selected Advanced=>Status tab in the very beginning, but after that VR300 WebGUI looks responsive.

I believe that you shouldn't be concerned about this - after all I doubt that you're re-configuring VR300 every day.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#5
Options
4 Reply
Re:Archer VR300 V2
2023-10-21 10:29:05
Can anyone answer me?
  0  
  0  
#2
Options
Re:Archer VR300 V2-Solution
2023-10-22 09:49:51 - last edited 2023-10-22 17:38:17

  @Huseyin_19 

 

The latest official FW for your VR300 v1.2 is V1.2_220407.

What you can do is to make a configuration backup of your modem. Update to the latest official FW version - V1.2_220407

Reset the device to its factory defaults and then restore its configuration from the backup you've made earlier:

 

 

Then test if the device is working as expected. You may have to switch to another web browser (Firefox, Chrome) to exclude a potential web browser issues.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#3
Options
Re:Archer VR300 V2
2023-10-22 09:56:19 - last edited 2023-10-22 10:00:30

I have done this before, unfortunately it doesn't work, every time I update to the latest version it takes almost 5 seconds to load between tabs.
https://youtu.be/05QCXau1zHA

  0  
  0  
#4
Options
Re:Archer VR300 V2-Solution
2023-10-22 17:26:37 - last edited 2023-10-22 17:38:10

  @Huseyin_19 

 

TBH I saw a little delay when you selected Advanced=>Status tab in the very beginning, but after that VR300 WebGUI looks responsive.

I believe that you shouldn't be concerned about this - after all I doubt that you're re-configuring VR300 every day.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#5
Options

Information

Helpful: 0

Views: 638

Replies: 4

Related Articles