Home

Forums

Stories

Knowledge Base

Home Network Community > DSL Modem Routers > Archer VR2100 vs WD4TB on NTFS

< DSL Modem Routers

Archer VR2100 vs WD4TB on NTFS

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR2100 vs WD4TB on NTFS

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AdamK81

2024-05-09 09:48:58 - last edited 2024-05-17 11:37:02

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Archer VR2100 vs WD4TB on NTFS

2024-05-09 09:48:58 - last edited 2024-05-17 11:37:02

Model: Archer VR2100

Hardware Version: V1

Firmware Version: 1.6.0 0.9.1 v009e.0 Build 220518 Rel.41627n

Hello,

I'm using router Archer VR2100 form few years,

I had connected hard drive WD 4TB with one NTFS partition to it for a long time,

From few weeks I have a new problem with it,

Drive is connected (as it was before), router can "see it", identify as WD Elements 2621, 3,6TB but... Aveliable 0,0 GB

If I will go to "drive shearing" it also shows that I can share 0GB

Of course I have connected hard drive directly to computer and it works without any problem - free space on drive 2,7TB

Maybe somebody have some ideas what can be the problem here?

It is something similar to topic

https://community.tp-link.com/en/home/forum/topic/229374

2 Accepted Solutions

AdamK81

LV1

2024-05-14 06:09:42 - last edited 2024-05-17 11:37:02

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Re:Archer VR2100 vs WD4TB on NTFS-Solution

2024-05-14 06:09:42 - last edited 2024-05-17 11:37:02

@terziyski

Ok, that could be the case but would then the same effect was when I connect drive to pc directly?

When I have try that connection - drive works normally, without any problem,

All data was there,

I was thinking about power level

Is it possible that voltage level on usb port in router is too low?

I understand that all electronical devices are waring out so maybe that could be the problem?

I thought that maybe I should buy usb connector with external power supply - what do You think?

Recommended Solution

AdamK81

LV1

2024-05-17 06:06:01 - last edited 2024-05-17 11:37:05

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Re:Archer VR2100 vs WD4TB on NTFS-Solution

2024-05-17 06:06:01 - last edited 2024-05-17 11:37:05

@terziyski

Hi,

Active USB hub have resolve the issue - so the problem was with limitation of power output from original USB connector in router,

Easy to fix - all equipment works,

Thanks for support,

Best Regards

Adam

Recommended Solution

6 Reply

terziyski

LV7

2024-05-12 22:56:52

Posts: 7025

Helpful: 5229

Solutions: 1160

Stories: 7

Registered: 2013-10-12

Re:Archer VR2100 vs WD4TB on NTFS

2024-05-12 22:56:52

@AdamK81

You can try to update VR2100 to its latest FW release - Archer VR2100(EU)_V1_240308 - here.

After updating the router FW check if the issue persists.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

AdamK81

LV1

2024-05-14 04:50:30

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Re:Archer VR2100 vs WD4TB on NTFS

2024-05-14 04:50:30

@terziyski

Hi,

I have tryed this firmware and still no effect,

This is what I have when I open "USB Devices"

Simultaneously i have this on main "Network map"

And the most strange thing - it works normally few weeks ago...

terziyski

LV7

2024-05-14 05:42:58

Posts: 7025

Helpful: 5229

Solutions: 1160

Stories: 7

Registered: 2013-10-12

Re:Archer VR2100 vs WD4TB on NTFS

2024-05-14 05:42:58

@AdamK81

I could only assume but probably something has gone wrong while using the HDD - power outage, wrongly recorded data, etc.

If that's the case reformatting the HDD probably may help.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

AdamK81

LV1

2024-05-14 06:09:42 - last edited 2024-05-17 11:37:02

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Re:Archer VR2100 vs WD4TB on NTFS-Solution

2024-05-14 06:09:42 - last edited 2024-05-17 11:37:02

@terziyski

Ok, that could be the case but would then the same effect was when I connect drive to pc directly?

When I have try that connection - drive works normally, without any problem,

All data was there,

I was thinking about power level

Is it possible that voltage level on usb port in router is too low?

I understand that all electronical devices are waring out so maybe that could be the problem?

I thought that maybe I should buy usb connector with external power supply - what do You think?

Recommended Solution

terziyski

LV7

2024-05-14 07:48:12

Posts: 7025

Helpful: 5229

Solutions: 1160

Stories: 7

Registered: 2013-10-12

Re:Archer VR2100 vs WD4TB on NTFS

2024-05-14 07:48:12

@AdamK81

This sounds reasonable too and you can try that as well.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

AdamK81

LV1

2024-05-17 06:06:01 - last edited 2024-05-17 11:37:05

Posts: 4

Helpful: 0

Solutions: 2

Stories: 0

Registered: 2024-05-09

Re:Archer VR2100 vs WD4TB on NTFS-Solution

2024-05-17 06:06:01 - last edited 2024-05-17 11:37:05

@terziyski

Hi,

Active USB hub have resolve the issue - so the problem was with limitation of power output from original USB connector in router,

Easy to fix - all equipment works,

Thanks for support,

Best Regards

Adam

Recommended Solution

Archer VR2100 vs WD4TB on NTFS

Archer VR2100 vs WD4TB on NTFS

Information

Voters 0

Tags