Home Network Community > Deco > Adding m% to XE75 Mesh but Ethernet wont work
< Deco

Adding m% to XE75 Mesh but Ethernet wont work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Adding m% to XE75 Mesh but Ethernet wont work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Adding m% to XE75 Mesh but Ethernet wont work
Adding m% to XE75 Mesh but Ethernet wont work
2024-05-15 12:08:57 - last edited 2024-05-16 08:41:40
Model: Deco M5  
Hardware Version: V1
Firmware Version:

Ive just installed and connected a Deco M5 to my Deco XE75 mesh. 

 

Firmware update completed but plugging in a NAS via the ethernet port on the M5 doesnt result in a connection. So I did a factory reset and it asked me for a firmware update which I did. It then connected the NAS for about 10 seconds then dropped the ethernet connection. It now refuses to reconnect the NAS. Cables are OK

 

I was advised that an M5 is ideal for this situation. Using WIFI>Ethernet on devices with no WiFi. Is this doable ?

 

Any advice appreciated

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Adding m% to XE75 Mesh but Ethernet wont work-Solution
2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

  @topgazza2 

Hi, Thanks for the feedback. The NAS should work when connecting via an Ethernet cable to the satellite M5.

Is NAS using DHCP to receive IP addresses?

There are 2 Ethernet ports on Deco M5 and did switching to another port make any difference?

By the way, are you able to temporarily connect the NAS to another satellite Deco XE75 to see whether the NAS could get an internet connection through the Ethernet cable?

Wait for your reply and best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options
2 Reply
Re:Adding m% to XE75 Mesh but Ethernet wont work-Solution
2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

  @topgazza2 

Hi, Thanks for the feedback. The NAS should work when connecting via an Ethernet cable to the satellite M5.

Is NAS using DHCP to receive IP addresses?

There are 2 Ethernet ports on Deco M5 and did switching to another port make any difference?

By the way, are you able to temporarily connect the NAS to another satellite Deco XE75 to see whether the NAS could get an internet connection through the Ethernet cable?

Wait for your reply and best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options
Re:Adding m% to XE75 Mesh but Ethernet wont work
2024-05-16 08:44:20

  @David-TP 

 

Thanks David

 

After I posted I found that I was having problems with a stable connection even if plugged into a LAN switch. By simple process of elimination everything pointed to the eithernet port on the motherboard. So I used an ethernet to USB C adapter and everything worked. Motherboard on its way back for a warranty replacement

 

Thanks for your reply

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 287

Replies: 2

Related Articles
Deco M5 unit wont connect to mesh anymore
560 0
Adding mesh WIFI
674 0
Adding an ethernet splitter
321 0
Adding Archer AX20 to Deco M5 mesh network
593 0
adding Deco 9's to Deco 5 mesh system
674 0
Deco mesh XE75 3-pack and Ethernet connection doubt
433 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.