Home Network Community > 5G/4G Routers > Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
< 5G/4G Routers

Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-05-27 18:02:43
Tags: #Network Connectivity
Model: TL-MR100  
Hardware Version: V2
Firmware Version: 1.3.0 0.9.1 v0001.0 Build 231101 Rel.58526n

Hi,

 

I use a TL-MR 100 (within the German O2 net) as Link Backup in combination with an ER605 Multi WAN Router. Since sometime (I can't figure out how long) in the protocoll there is the message "USER: no need to init device sca" written every second (or even more often). What is the meaning? And how can I stop it because it dump the protocoll within only some minutes (26 pages in just 5 minutes)?
Any Idea is appreciated.

Note: In the moment there is a limited bandwith to the O2 network because the tariff is finally not set but connectivy is generally available

 

BR

Ingo
 

  0      
 
  0      
 
#1
Options
5 Reply
Re:Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-05-28 07:36:27

  @Intigona 

 

Hi, thanks for posting question here.

Only according to the message, we can not locate the issue.

Can your TL-MR100 work properly? 

You may monitor the performance and send us the whole system log if necessary.

 

Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode.
  0  
  0  
#2
Options
Re:Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-05-28 17:19:29

 Hi  @Marvin_S ,

 

as far as I can see, Router works proberly. Ping to the Internet works fine but I can't make a speedtest yet because my Highspeed tarif start from mid of June.

 

The think is, that I can't see, if there are other problems with the connection because within 20 min the log is full of messages like in the subject stated. Here is a short output with 20 messages injust 23 sec.:

2024-05-28 19:11:49 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:51 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:52 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:53 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:54 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:58 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:58 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:58 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:59 [6] 4G: USER: no need to init device sca

2024-05-28 19:11:59 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:05 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:05 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:06 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:06 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:08 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:08 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:09 [6] 4G: USER: no need to init device sca

2024-05-28 19:12:12 [6] 4G: USER: no need to init device sca

any idea is appreciated

BR

Ingo

  0  
  0  
#3
Options
Re:Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-05-30 11:42:00

Just to add: After changing the protocol level one up, there is no more information about "USER: no need to init device sca" and the router works fine the rest of the day. Just a reconnect in the night obviously initiated from the provider.

  0  
  0  
#4
Options
Re:Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-07-29 17:24:16

  @Intigona Please could you provide more details about what was the change, what does it means " After changing the protocol level one up," i can not understand how to find this setting on the appliance

Thanks!!!

  0  
  0  
#5
Options
Re:Constant Message "USER: no need to init device sca" Spaming system protocoll at TL-MR100
2024-07-29 17:42:06

  @Intigona 

 

I changed in the Log Settings the minimum level from "Information" to "Notic" and the spaming stopped

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 2377

Replies: 5

Tags

Network Connectivity
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.