Home

Forums

Stories

Knowledge Base

Business Community > Controllers > Issues setting up Mullvad on OC200 - Traffic Not Routing

< Controllers

Issues setting up Mullvad on OC200 - Traffic Not Routing

RLGRIME

2024-08-24 15:28:37 - last edited 2024-08-27 03:41:26

Posts: 3

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2024-08-24

Issues setting up Mullvad on OC200 - Traffic Not Routing

2024-08-24 15:28:37 - last edited 2024-08-27 03:41:26

Tags: #VPN

Model: OC200

Hardware Version:

Firmware Version: 2.14.4

Hello all! I am attempting to setup Mullvad as the only route for all traffic out of my network via a OC200 Hardware controller. I will provide the information I have so far below.

Network Topology:

Omada OC200 HC
Omada ER605 vpn router
Omada EAP610
Omada switch

ISP: comcast

Things I have tried so far via the controller interface:

1. **VPN Configuration**:
   * **Type**: Client-to-Site
   * **Protocol**: OpenVPN (Client)
   * **Interface/IP LAN**: WAN
   * **Authentication**: Certificate + Account
   * **Username/Password**: Added
   * **Remote Server**: [198.44.128.98:1302](http://198.44.128.98:1302)
   * **Local Networks**: Set to all
   * **Imported .ovpn file provided by mullvad**
2. **Policy Routing**:
   * **Protocols**: All
   * **WAN**: WAN
   * **Source Type**: Network (selected my local network)
   * **Destination Type**: IP Group (selected IPGroup\_Any)

Am I missing something? Please keep in mind I am not a network admin by trade, and I am pretty new to home networking in general, so if I am missing a piece of equipment or configuration please let me know and I can buy/implement and test.

1 Accepted Solution

Hank21

2024-08-26 08:06:32 - last edited 2024-08-27 03:41:26

Posts: 3673

Helpful: 719

Solutions: 497

Stories: 8

Registered: 2021-12-13

Re:Issues setting up Mullvad on OC200 - Traffic Not Routing -Solution

2024-08-26 08:06:32 - last edited 2024-08-27 03:41:26

@RLGRIME

Currently, if you configure Open VPN as a client, the VPN Server cannot serve as a proxy gateway for backend clients. Consider using L2TP or PPTP to meet this need.After setting up the VPN, you may pick the VPN tunnel as the WAN interface for policy routing rules.

How to configure Omada Gateway as a PPTP/L2TP VPN Client to enable the VPN Server as Proxy Gateway for backend clients

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

RLGRIME

LV1

2024-08-26 14:51:04

Posts: 3

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2024-08-24

Re:Issues setting up Mullvad on OC200 - Traffic Not Routing

2024-08-26 14:51:04

@Hank21 thank you so much for your response, this is exactly what I was looking for. I will try this tonight and report back. Thank you!

RLGRIME

LV1

2024-08-26 16:45:36

Posts: 3

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2024-08-24

Re:Issues setting up Mullvad on OC200 - Traffic Not Routing

2024-08-26 16:45:36

Hey one more question while I have you here ☺️ Does the controller support dns over https or tls? Is there a guide for this as well? Mullvad offers this and I would like to take advantage if I can. Thank you again!