Solution Satellite Deco Units Work Well but Display Offline on the Deco APP
This Article Applied to:
Deco M4/M5/M9 Plus, Deco X50/Deco X50-Outdoor etc.
Phenomenon Description:
The satellite Decos are solid green(or white) and work well but they are displayed "Offline" on the Deco APP.
Available Solutions:
-
The official firmware will be released later to optimize this issue.
-
Based on the feedback we've received, the majority of issues are related to the abundance of smart home devices, particularly Tapo smart devices. To address this, we recommend installing the following beta firmware as a temporary solution:
| Deco P9_V2 | 1.2.1_build_20240925_Beta |
| Deco S4_V2 | 1.6.2_build_20240828_Beta |
| Deco M4_V2 | 1.6.2_build_20240828_Beta |
| Deco M4_V3 | 1.6.1_build_20240904_Beta |
| Deco S4/M4_V4 | 1.1.2_build_20240828_Beta |
| Deco M5_V1/V2/V3 | 1.7.8_build_20240826_Beta |
| Deco M9 Plus V1 | 1.6.3_build_20240715_Beta |
| Deco M9 Plus V2 | 1.6.3_build_20240715_Beta |
| Deco PX50(US)_V1 | 1.2.4_build_20240819_Beta |
| Deco PX50(EU)_V1 | 1.2.4_build_20240819_Beta |
| Deco X10/X15/X1500/W4500_V1 | 1.1.7_build_20240911_Official |
| Deco X20_V2 | 1.2.5_build_20240724_Beta |
| Deco X20_V3 | 1.2.1_build_20240827_Beta |
| Deco X20_V4 | 1.5.5_build_20240816_Beta |
| Deco X50/Deco X55_V1 | 1.6.1_build_20241010_Official |
| Deco X50/Deco X55_V1.2 | 1.4.5_build_20241021_Beta |
| Deco X60_V2 | 1.5.3_build20240728_Beta |
| Deco X60_V3 |
1.3.0_build_20241018_Beta |
| Deco X50-Outdoor_V1 | 1.2.5_build_20240725_Beta |
| Deco X50-POE_V1 | 1.2.5_build_20241031_Beta |
| Deco X50-POE_V2 | 1.0.6_build_20240822_Beta |
| Deco XE75/XE5300_V1 | 1.4.1_build20240926_Beta |
| Deco XE75 V2/XE5300 V2 | 1.2.8_build_20240730_Beta |
| Deco XE75 Pro V2/XE75 Pro V3 | 1.2.12_build_20240821_Beta |
| Deco BE63/BE65_V2 | 1.1.0_build _20240923_Official |
| Deco BE85_V2 | 1.1.1_build_20241023_Official |
Note:
1. Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
2. It is recommended that all Decos in the network be upgraded to beta firmware.
3. Please also check whether there is a firmware update for the Tapo device in the Tapo APP. If so, please update the Tapo device to the latest firmware.
4. How to update the satellite Deco units:
When the satellite Decos are offline, they may not be successfully upgraded through the Web UI. In this case, it is recommended to upgrade according to the following steps:
- Please temporarily power off most of the smart home devices and wait for the satellite Deco come back online.
- Once all the satellite Deco units are confirmed online, try upgrading to the beta firmware again through the Web UI.
-If the main Deco and satellite Deco units are on different models, you could also update the satellite units individually through its IP address.
- After ensuring that all Deco units have been successfully upgraded, power on the Tapo devices again and observe if the issue is resolved.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, Thank you very much for sharing with us. I do appreciate users try to share what they have found about the Deco Mesh system
.
Currently, the engineer is trying to optimize the APP management experience so they launched a new beta APP test. I think it would be the right time to check whether there is any glitches when Deco APP tried to deliver the required setting to the Deco hardware.
It would be highly appreciated if you could try to install the beta APP here and share the feedback:
Deco APP 3.8.36 --- Greatly Optimized Network Management Experience
Thanks again and best regards.
- Copy Link
- Report Inappropriate Content
Left feedback in App Beta section
- Copy Link
- Report Inappropriate Content
Hi,
Does new beta version of Deco x50 v1.2 firmware also have this fix for this particular problem or do I need to choose fix this problem or stay in 1.2 beta?
Thanks!
- Copy Link
- Report Inappropriate Content
@David-TP but this not mash connect to mr4
- Copy Link
- Report Inappropriate Content
Only master Deco P9 is online in the APP after updating firmware to latest beta. Updating APP to the latest beta doesn't fix the situation.
| Deco P9_V2 | 1.2.1_build_20240904_Beta |
- Copy Link
- Report Inappropriate Content
Same, my P9. The main one only works in app. Others appear offline.
Updated to beta on the app and made no difference.
Is there an even newer firmware yet, to even try to fix this ?
I'm 100% sure my actual network is suffering. I took one P9 off to try and reconnect but that won't even join again now.
- Copy Link
- Report Inappropriate Content
Nytram wrote
I'm 100% sure my actual network is suffering. I took one P9 off to try and reconnect but that won't even join again now.
I've managed to reconnect P9 slave device to the network with beta firmware installed using the following procedure:
1. Reset slave device.
2. Create new network in Deco app using this slave device as master.
3. Login in to the master device of the newly created network using browser and its IP address.
4. Downgrade the master device to the latest non beta firmware through the browser.
5. Reset it.
6. Now you can add the device to the network with master on beta firmware. Newly added device will be even shown online in the App.
- Copy Link
- Report Inappropriate Content
What about XE75 Pro v1? Does it have the same problem? I just see the firmware update for v2 and v3.
- Copy Link
- Report Inappropriate Content
Hi, I haven't received similar feedback on the Deco XE75 Pro yet.
Did you experience the current issue on your Deco XE75 Pro?
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 5643
Replies: 68
Voters 1
