Home Network Community > Deco > How to make the “guest network” work well?
< Deco

How to make the “guest network” work well?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to make the “guest network” work well?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to make the “guest network” work well?
How to make the “guest network” work well?
2024-09-08 14:41:35 - last edited 2024-09-12 10:58:02
Model: Deco X20   Deco E4  
Hardware Version: V3
Firmware Version: 1.2.1 Build 20240723 Rel. 64983

I have a deco network with topology as below

 

i use X20 for Main Deco and E4 for another deco

 

ignore "Masjid Belakang" and "R2" units, because im turning it off, in this topology i not use switch or anything, i just connet via LAN port on deco

the connection is like from Internet -> MainDeco(Port 1), MainDeco(Port 2) -> Ruangtengah(Port1), Ruangtengah(Port2) -> R1(port1), R1(port 2) -> R2(port1), R2(port2) -> R3(port1), R3(port2) -> R4(port1)

why guest network just can acces from MainDeco and Ruangtengah ? do I have to provide a switch after the “Main Deco” and connect all Deco to the switch and do VLAN settings?
or is there another way of setting so that the “guest network” can be accessed from all decos? 
 

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:How to make the “guest network” work well? -Solution
2024-09-10 06:15:49 - last edited 2024-09-12 10:58:02

  @Fawwaz_Ijlal_M 

Hi, Thank you very much for the update.

Here is a beta firmware for Deco E4 V1/V2.:

https://static.tp-link.com/upload/beta/2024/202403/20240313/e4r_ver1-6-1_240313_beta.zip

It is suggested to install this beta firmware on all the satellite Deco E4 to see whether it helped.

 

Wait for your reply and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#5
Options
5 Reply
Re:How to make the “guest network” work well?
2024-09-09 03:51:30

  @Fawwaz_Ijlal_M 

Hi, Thanks for the feedback.

It should work without the network switch.

How about the main Wi-Fi network? Would the devices be able to connect to the main network of the satellite Deco units?

 

By the way,  Did Deco work in wireless router mode? Have you tested on different mobile devices to see whether they all had the similar issue?

 

Wait for your reply and best regards.

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:How to make the “guest network” work well?
2024-09-09 13:01:10
1. all devices are normal on the main wifi network on all deco satellites 2. Yes, my deco working on router mode 3. i try in many devices but the “guest network” can only connect if i connect to “Main Deco” and “Middle Room”
  0  
  0  
#3
Options
Re:How to make the “guest network” work well?
2024-09-09 13:29:52
4. when connecting to the “guest network”, the mobile device shows “getting ip address..” after that it fails.
  1  
  1  
#4
Options
Re:How to make the “guest network” work well? -Solution
2024-09-10 06:15:49 - last edited 2024-09-12 10:58:02

  @Fawwaz_Ijlal_M 

Hi, Thank you very much for the update.

Here is a beta firmware for Deco E4 V1/V2.:

https://static.tp-link.com/upload/beta/2024/202403/20240313/e4r_ver1-6-1_240313_beta.zip

It is suggested to install this beta firmware on all the satellite Deco E4 to see whether it helped.

 

Wait for your reply and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#5
Options
Re:How to make the “guest network” work well?
2024-09-12 10:57:55
aaa oke.., thanks. it is work
  0  
  0  
#6
Options

Information

Helpful: 1

Views: 648

Replies: 5

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.