Home Network Community > Deco > Deco running slow or not at all with wired backhaul
< Deco

Deco running slow or not at all with wired backhaul

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco running slow or not at all with wired backhaul

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco running slow or not at all with wired backhaul
Deco running slow or not at all with wired backhaul
2025-02-23 21:58:07
Model: Deco BE65  
Hardware Version:
Firmware Version: 1.0.8 Build 20240723 Rel. 26458

Hello,

 

I have three Deco BE65 units with the following topography:

 

 

When set up like this, everything works fine. However, as soon as I wire the 'living room' and 'garage end' Decos together, instead of allowing them to connect wirelessly, every device connected to the 'garage end' and 'bedroom end' Decos connects to the internet incredibly slowly, or not at all.

 

I've tried using a different network cable between the 'garage end' and 'living room' units, but the outcome is the same.

 

Is there any way I can diagnose what's going on and why it runs so poorly when connected via an ethernet cable?

 

Thanks.

  1      
 
  1      
 
#1
Options
7 Reply
Re:Deco running slow or not at all with wired backhaul
2025-02-24 00:34:55

  @neilbaker86 

 

To make sure everything is fine with your Deco mesh setup in general, question: did you name your Satellite Deco as "Deco_71A0" and "Deco_7434?"

 

Because, usually if everything is right, one will see Satellite Deco named similar to what I have in my Deco app:

 

  1  
  1  
#2
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-24 06:23:44

  @neilbaker86 

Hi, It is also suggested to install the 1.1.0 version here:

Deco BE65_V1_1.1.0 Supported WireGuard VPN, Channel Selection and Matter

After that, you could try to temporarily power off "Bedroom" Deco_7434 when trying to connect the "Garage" Deco_71AD to see whether the Ethenet Backhaul works this time, then power back "Bedroom" Deco_7434.

 

Thank you very much and best regards.

▶Check What's Currently Going on With Deco ▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience ▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-24 13:40:56

  @neilbaker86 Do you have any other network appliance (router, switch) in addition to the three Deco?

  0  
  0  
#4
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-25 00:00:35 - last edited 2025-02-25 00:00:52

The ‘living room’ Deco is connected (wired) to the Virgin media hub. No other network devices are connected to it.

  0  
  0  
#5
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-25 00:04:22
I only added the garage end and bedroom end bits to the names. The other bit is what they called themselves.
  0  
  0  
#6
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-25 06:47:35

  @neilbaker86 Is the wifi active on the Virgin media hub?  If yes, do you have same issue when you disable it?

  0  
  0  
#7
Options
Re:Deco running slow or not at all with wired backhaul
2025-02-25 11:38:14

  @yves_b No, I disabled the Wi-Fi on the Virgin media hub some time ago, but it makes no difference anyway.

  0  
  0  
#8
Options

Information

Helpful: 1

Views: 619

Replies: 7

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.