<
Deco
Deco M4_V1/V2_1.8.0 User Feedback
Deco M4_V1/V2_1.8.0 User Feedback
Posts: 16374
Helpful: 2350
Solutions: 2443
Stories: 9
Registered: 2020-04-14
2025-08-20 03:09:39 - last edited 2025-08-20 03:33:05
Posts: 16374
Helpful: 2350
Solutions: 2443
Stories: 9
Registered: 2020-04-14
Deco M4_V1/V2_1.8.0 User Feedback
2025-08-20 03:09:39 - last edited 2025-08-20 03:33:05
Tags:
This Article applies to
Deco M4_V1/V2
Firmware Modifications:
- Enhanced System Security
- Improved Client management experience on the Deco APP.
- Fixed the issue that the IPv6 communication between client devices might fail when the assigned type was set to DHCPv6.
- Fixed the issue that the real-time speed rate was "--/--" in the Deco APP.
Note: This version upgrade is irreversible, and you cannot downgrade to the previous firmware after the upgrade.
Firmware Version:
| Deco M4_V1/V2 | 1.8.0 Build 20250721 Rel. 49216 |
As the previous post about version 1.7.0 was too long to navigate for information on the newly released 1.8.0 version, I have created this new post. Kindly share your feedback on how the new 1.8.0 works. Your input will greatly benefit other users.
Thank you very much.
▶Check What's Currently Going on With Deco
▶Parental Control Upgrade on HomeCare Models
▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience
▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security
▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More
Try to leave a Message if urgent help is required.
#1
Options
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thread Manage
Announcement Manage
43 Reply
Posts: 3
Helpful: 1
Solutions: 0
Stories: 0
Registered: 2025-10-31
Re:Deco M4_V1/V2_1.8.0 User Feedback
Saturday
@ARGamingPK1 thank you! I downloaded and installed the firmware 1.8.1.
However, the speed problem on the 5G network persists. The maximum speed only reaches 200mb. My network is 650mb, and on 5G it used to reach around 300mb to 350mb, but now it doesn't exceed 200mb.
I don't know what they did in these last updates, but it's not good and it lost a lot of performance 
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#42
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 787
Helpful: 346
Solutions: 28
Stories: 0
Registered: 2023-12-03
Re:Deco M4_V1/V2_1.8.0 User Feedback
Saturday
@wmosquini Check QoS settings if the speed limit is set you can turn OFF Qos Settings or change the speed limit to 1000 Mbps.
Please & Thank You !! ❤️
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#43
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 371
Helpful: 152
Solutions: 2
Stories: 0
Registered: 2024-02-23
Re:Deco M4_V1/V2_1.8.0 User Feedback
6 minutes ago
@David-TP any news for deco x50v1.30.....!?
Sayeem Ahmed
from Bangladesh
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#44
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 16374
Helpful: 2350
Solutions: 2443
Stories: 9
Registered: 2020-04-14
2025-08-20 03:09:39 - last edited 2025-08-20 03:33:05
Posts: 16374
Helpful: 2350
Solutions: 2443
Stories: 9
Registered: 2020-04-14
Information
Helpful: 15
Views: 2822
Replies: 43
Voters 3
Tags
Report Inappropriate Content
Transfer Module
New message