Deco M4_V1/V2_1.8.0/1.8.1/1.8.2 User Feedback
This Article applies to
Deco M4_V1/V2
Firmware Modifications:
- Enhanced System Security
- Improved Client management experience on the Deco APP.
- Fixed the issue that the IPv6 communication between client devices might fail when the assigned type was set to DHCPv6.
- Fixed the issue that the real-time speed rate was "--/--" in the Deco APP.
Note: This version upgrade is irreversible, and you cannot downgrade to the previous firmware after the upgrade.
Firmware Version:
| Deco M4_V1/V2 | 1.8.0 Build 20250721 Rel. 49216 |
| Deco M4_V1/V2 | 1.8.1 Build 20250829 Rel. 44659 |
| Deco M4_V1/V2 | 1.8.2 Build 20251027 Rel. 36869 |
As the previous post about version 1.7.0 was too long to navigate for information on the newly released 1.8.x versions, I have created this new post. Kindly share your feedback on how the new 1.8.x work. Your input will greatly benefit other users.
Thank you very much.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@ARGamingPK1 thank you! I downloaded and installed the firmware 1.8.1.
However, the speed problem on the 5G network persists. The maximum speed only reaches 200mb. My network is 650mb, and on 5G it used to reach around 300mb to 350mb, but now it doesn't exceed 200mb.
I don't know what they did in these last updates, but it's not good and it lost a lot of performance 
- Copy Link
- Report Inappropriate Content
@wmosquini Check QoS settings if the speed limit is set you can turn OFF Qos Settings or change the speed limit to 1000 Mbps.
- Copy Link
- Report Inappropriate Content
@David-TP any news for deco x50v1.30.....!?
- Copy Link
- Report Inappropriate Content
@ARGamingPK1
I'm sorry, but firmware 1.8.1 didn't help. Mine had QoS configured to 1000mb. I chose to disable it, but the problem still persists. It's surreal how TP-Link managed to mess up the device (excuse the rant).
Literally, everything is bad. Playing online games is laggy. Watching videos is choppy. I work from home and frequently have calls, and everything starts to freeze. It's disappointing and I regret the moment I clicked on the upgrade notification.
I tried to downgrade via web access to version 1.6.5, but it's not allowed. Is there any way to do this?
- Copy Link
- Report Inappropriate Content
@wmosquini Yeah you can install 1.6.5 by using Recovery Mode and i think you can do factory reset and do the setup again on 1.8.1 firmware or you can try AP Mode.
- Copy Link
- Report Inappropriate Content
Just installed Firmware Version 1.8.2 Build 20251027 Rel. 36869
Looking good 👍
M4R x2
- Copy Link
- Report Inappropriate Content
@Bugs22 Where did u get that?
- Copy Link
- Report Inappropriate Content
@ARGamingPK1 just popped up on my deco app as available so all done via app on both devices. Bit glitchy when it came up but now stable. Before that I think I was on 1.8..
- Copy Link
- Report Inappropriate Content
@Bugs22 Beta firmware 1.8.2 is buggy and glitchy because of they added VPN in this firmware.
- Copy Link
- Report Inappropriate Content
@ARGamingPK1 How do we know this is Beta? And why is this being pushed to production devices automatically?!
ps: cant see any VPN options. perhaps because I am in AP mode instead of router.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 15
Views: 3971
Replies: 60
Voters 3
