How to execute "flash set" commands in XX530v?
How to execute "flash set" commands in XX530v?
I've updated to latest firmware, but can't run these commands:
flash set OMCI_FAKE_OK 1
flash set OMCI_OLT_MODE 1
flash set GPON_PLOAM_PASSWD 0123456789
flash set GPON_SN XXXXXXXXXXXXXX
flash set GPON_ONU_MODEL HG8010H
flash set PON_VENDOR_ID HWTC
flash set OMCI_SW_VER1 V3R015C10S106
flash set OMCI_SW_VER2 V3R015C10S106
flash set CUSTOM_OMCI_SW_VER1 V3R015C10S106
flash set CUSTOM_OMCI_SW_VER2 V3R015C10S106
flash set HW_HWVER 635.A
flash set ELAN_MAC_ADDR XXXXXXXXXXXX
I must run these commands for my ISP accept my device!
Please help.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
KaleviHeikkinen wrote
@KaleviHeikkinen Im doing my research to try find something, but its hard. No success until now.
- Copy Link
- Report Inappropriate Content
@reffsZA Web page for XX530v mentions it supports OMCI. Isn't support for this commands what OMCI is all about?
- Copy Link
- Report Inappropriate Content
Hello @VladimirPopescu ,
As I know, OMCI is a standardized protocol (G.988) defined by the ITU-T for remote management of ONUs/ONTs by the OLT over a GPON network. Its functionality is limited by the standard's Management Information Base (MIB). The flash set command is typically a vendor-provided command-line interface (CLI) for the device.
While GPON devices support OMCI (ONT Management and Control Interface), it does not necessarily support vendor-specific flash set commands.
- Copy Link
- Report Inappropriate Content
Joseph-TP wrote
Hello @VladimirPopescu ,
As I know, OMCI is a standardized protocol (G.988) defined by the ITU-T for remote management of ONUs/ONTs by the OLT over a GPON network. Its functionality is limited by the standard's Management Information Base (MIB). The flash set command is typically a vendor-provided command-line interface (CLI) for the device.
While GPON devices support OMCI (ONT Management and Control Interface), it does not necessarily support vendor-specific flash set commands.
@Joseph-TP But aren't these commands available in an another way, so that they end up doing same thing? This is what we need.
- Copy Link
- Report Inappropriate Content
MacielJunior wrote
Joseph-TP wrote
Hello @VladimirPopescu ,
As I know, OMCI is a standardized protocol (G.988) defined by the ITU-T for remote management of ONUs/ONTs by the OLT over a GPON network. Its functionality is limited by the standard's Management Information Base (MIB). The flash set command is typically a vendor-provided command-line interface (CLI) for the device.
While GPON devices support OMCI (ONT Management and Control Interface), it does not necessarily support vendor-specific flash set commands.
@Joseph-TP But aren't these commands available in an another way, so that they end up doing same thing? This is what we need.
@MacielJunior They aren't. You can barely turn wifi on or off with telnet, and ssh is not available. It should be possible to run similar commands to change this options. Lots of onus have more options than what TP-Link offers I'm afraid.
- Copy Link
- Report Inappropriate Content
@reffsZA I need to know this too. Is there some news about it?
- Copy Link
- Report Inappropriate Content
michalski wrote
@reffsZA I need to know this too. Is there some news about it?
@michalski no news yet, I believe! Lets wait...
- Copy Link
- Report Inappropriate Content
gijuruna wrote
@reffsZA These commands don't work in tp link I think.
There's the Tp-link Xz000 G3 where you can set some of these settings via web UI, but it's a simpler device, with no wifi, but those specific commands don't work in any Tp Link anyway.
@gijuruna G3 is told to have more options, but it needs a router to work. Thats the sad part
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 3062
Replies: 18
Voters 0
No one has voted for it yet.