Home Network Community > Deco > Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
< Deco

Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien

Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien

Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
a week ago
Model: Deco BE25  
Hardware Version: V1
Firmware Version: 1.1.0 build 20250718 rel 40387

Besoin d'aide pour connecter des  caméra au réseau Wi-Fi, après la mise a jour 1.1.0 rien ne marche plus , avec la version firmware 1.0.2 tout allés très bien

  1      
 
  1      
 
#1
Options
3 Reply
Re:Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
Tuesday

  @joan01 

Hi, welcome to the community.

Is the LED on Deco BE25 still solid green?

Can I have the model number of the smart WiFi cameras?

Would there be any error message when it failed to connect to Deco?

 

Here are some suggestions for your reference:

  • Enable IoT Network and set the "Security" to "WPA2 only"
  • Set the WiFi channel under Main WiFi>2.4Ghz band>2.4GHz channels settings> channel 11 and channel width 20MHz

 

Wait for your reply.

Best regards. 

▶Check What's Currently Going on With Deco ▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience ▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
Tuesday

  @David-TP 

 

Hi, DAVID 
thanks for the reply
 

Is the LED on Deco BE25 still solid green? YES

Can I have the model number of the smart WiFi cameras? Dahua  P5AS-PV

Would there be any error message when it failed to connect to Deco? Nope

 

Here are some suggestions for your reference:

  • Enable IoT Network and set the "Security" to "WPA2 only" Done and not working 
  • Set the WiFi channel under Main WiFi>2.4Ghz band>2.4GHz channels settings> Done same result

    channel 11 and channel width 20MHz ??? I can change from 160 to 80 MHz, no effect, the channel I can't change the channel,  but in the web interface it is set to channel 3 

    After the firmware 1.1.0 update, nothing works anymore. With the firmware version 1.0.2, everything is was fine, 
    I just need to rollback the firmware go back to 1.0.2 or something like that 

    I have use BE25's in like 7 location like 28 BE25 Total for the past two years all good, until 1.1.2 

 

  • Thanks 
  1  
  1  
#3
Options
Re:Wi-Fi, après la mise a jour1.1.0 rien ne marche plus ,avec la version1.0.2 tout alles tres bien
Tuesday

  @joan01 

Hi, thanks for the quick reply.

It seems like you have contacted the local technical support before, and now the case has been escalated to the senior engineer for further assistance.

Please check the email later for more suggestions.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience ▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options

Information

Helpful: 1

Views: 89

Replies: 3

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.