Home Network Community > DSL Modem Routers > cant acces to the router interface
< DSL Modem Routers

cant acces to the router interface

cant acces to the router interface

cant acces to the router interface
cant acces to the router interface
2025-11-01 08:35:36 - last edited Thursday
Tags: #Web GUI Management
Model: Archer VR300  
Hardware Version: V2
Firmware Version:

Hello,

I’m currently unable to access the web interface of my TP-Link Archer VR300 modem. I’ve tried the default gateway addresses (192.168.1.1 and 192.168.0.1), but neither works. I’ve tested both wired and wireless connections, restarted the modem, and cleared my browser cache, yet the problem persists.

I can connect to the modem, but I can’t access the internet or reach the management interface. Could you please help me determine what might be causing this issue or suggest any recovery steps?

Thank you in advance for your support.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:cant acces to the router interface-Solution
Thursday - last edited Thursday

  @soumatou ,

As a supplement, please unplug the Ethernet cable from the WAN port. Then, hard reset the VR300: Press and hold down the reset button for about 2 seconds to reset the modem router to factory default settings.

Please try to log in to the web interface again.

 

If it still doesn't help, please contact your local support for further assistance.

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:cant acces to the router interface
2025-11-02 19:16:55 - last edited 2025-11-02 20:15:07

  @soumatou 

 

Try the http://tplinkmodem.net/ while connected to the modem (wired or wireless).

If this still doesn't work, you may need to reset the VR300 to its factory defaults and reconfigure from scratch.

If after resetting you still can't access VR300 WebGUI, contact your local support for further assistance.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:cant acces to the router interface
2025-11-02 19:25:35

  @terziyski Thank you for your answer but I already tried those steps 

  0  
  0  
#3
Options
Re:cant acces to the router interface-Solution
Thursday - last edited Thursday

  @soumatou ,

As a supplement, please unplug the Ethernet cable from the WAN port. Then, hard reset the VR300: Press and hold down the reset button for about 2 seconds to reset the modem router to factory default settings.

Please try to log in to the web interface again.

 

If it still doesn't help, please contact your local support for further assistance.

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 203

Replies: 3

Tags

Web GUI Management
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.