AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem

AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem

AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem
AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem
2026-01-17 17:39:53 - last edited 2026-02-11 02:15:20
Model: Archer AX55   LS1005G  
Hardware Version: V1
Firmware Version: 1.5.10

Hi,
I've set up the Easy Mesh with two AX55 routers. When I connect them directly to each other, I have a mesh built via Ethernet, but when I take the satellite router and plug it in another room, it only builds a mesh via wi-fi, all machines are connected through the LS105G switch. Any other device connected to ethernet cable anywhere have internet connection. Both routers are quite far away from each other, so the Mesh via wifi is not very stable

0
0
#1
1 Accepted Solution
Re:AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem-Solution
2026-01-19 06:29:30 - last edited 2026-02-11 02:15:20

Hi @easyff ,

Welcome to our community.

 

There might be a connection problem between the Switch and the Satellite router. Please try the following suggestions:
1. Check Your Ethernet Cabling:
• Make sure the Ethernet cable between the switch and the satellite device is working properly. Try swapping cables to rule out any faults.

2. Use Different Ethernet Ports:
• Test different LAN ports on both the switch and satellite routers for the backhaul connection to ensure the correct port is being used.

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click Or ☆Recommended Solution if the post/answer helps.
Recommended Solution
0
0
#2
1 Reply
Re:AX55 to AX55 ethernet backhaul for easymesh via LS105G switch problem-Solution
2026-01-19 06:29:30 - last edited 2026-02-11 02:15:20

Hi @easyff ,

Welcome to our community.

 

There might be a connection problem between the Switch and the Satellite router. Please try the following suggestions:
1. Check Your Ethernet Cabling:
• Make sure the Ethernet cable between the switch and the satellite device is working properly. Try swapping cables to rule out any faults.

2. Use Different Ethernet Ports:
• Test different LAN ports on both the switch and satellite routers for the backhaul connection to ensure the correct port is being used.

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click Or ☆Recommended Solution if the post/answer helps.
Recommended Solution
0
0
#2