Home

Forums

Stories

Knowledge Base

Home Network Community > DSL Modem Routers > Help with bridge mode td-w8950n

< DSL Modem Routers

Help with bridge mode td-w8950n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Help with bridge mode td-w8950n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

kitalor

2016-10-03 10:03:53

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Help with bridge mode td-w8950n

2016-10-03 10:03:53

Model : Model No. TD-W8950N

Hardware Version : TD-W8950N V1 0x00000001

Firmware Version : 1.1.1 Build 160203 Rel.51377

ISP : tpg australia

Hello
I am attempting to put this modem into full bridge mode to use with an asus router ac68u (through ethernet) but I am having some issues.

I can start from factory default -quick setup enter vpi and vci and set to bridging this way.

However something is not right as after resetting and connecting router I get access but its very unstable. Are there additional settings to be concerned about?

I have ruled out the router as I am currently using another (asus) modem in bridge mode and everything is working. I want to get the w8950n working though as that has the chipset more suited to my adsl2 connection

Any help greatly appreciated!

1.1.1 Build 160203 Rel.51377

4 Reply

kitalor

LV1

2016-10-05 15:31:21

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-05 15:31:21

Hello---- echo ---- anybody out there???
THis has been drivingg me insane!!!!!!!!!:mad::mad::mad::mad::mad::mad::mad::mad::mad::mad::mad:
I think I solved it. so after a hard reset for whatever reason all the data isn't cleared..
If I go to advance setup - wan service I get one of these;

Interface	Description	Type	Vlan8021p	VlanMuxId	Igmp	NAT	Firewall	IPv6	Mld	Remove	Edit
atm0.1	br_0_8_35	Bridge	N/A	N/A	Enabled	Disabled	Disabled	Disabled	Disabled

Now this would be there even after a hard reset so I removed it and then went to the quick setup and did a bridge and now everything appears to be stable

now I seem to be able to access both my router and my modem on differnet ip's.

Is this normal? Does it mean I'm not fully bridged?

kitalor

LV1

2016-10-05 19:07:36

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-05 19:07:36

still not solved

jimasek

LV5

2016-10-07 03:04:29

Posts: 2171

Helpful: 87

Solutions: 0

Stories: 0

Registered: 2013-01-12

Re:Help with bridge mode td-w8950n

2016-10-07 03:04:29

I'd like to see some of screenshots from your router setup

kitalor

LV1

2016-10-07 07:18:22

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-07 07:18:22

Thanks for replying!

http://imgur.com/mdopoli
http://imgur.com/r0dL6NU

I believe I have fixed it. The problem was a dell laptop on the network. It had all sorts of problems after upgrading to windows 10.
I think it was casuing an ip conflict causing modem hangups? I had no idea such a thing was possible
Installed fresh ssd and windows 10 on this laptop and there are no error entries in the router log from the last 24 hours

Help with bridge mode td-w8950n

Help with bridge mode td-w8950n

Information

Voters 0

Tags