Home Network Community > All Threads > Can't reach my unmanaged swith
< All Threads

Can't reach my unmanaged swith

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can't reach my unmanaged swith

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can't reach my unmanaged swith
Can't reach my unmanaged swith
2019-07-19 17:52:44 - last edited 2019-07-23 01:33:09
Model: TL-SG1016D  
Hardware Version:
Firmware Version:

Hi,

First of all, excuse my poor english.

I need help to configure my switch

My lan is composed by a modem/router Huawei B525s-23a, my pc and 2 switches TL-SG1016D (unmanaged)

I have installed both the switches, one is actually turned off (in order to configure the first one and avoid a ip conflict) and the second one is connected to the modem (link indicator green and blinking) , also my pc is connected to the modem (by cable).

According to the installation manual my subnet mask is 255.255.255.0, my gateway ip is 192.168.0.2, and the pc ip is assigned by DHCP (range 192.168.0.100-192.168.0.200).

All I need is to configure my switch, but I can't connect to 192.168.0.1 (connection time out).

 

Do you have any idea about what is wrong?

 

Thanks,

Paolo

 

 

 

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Can't reach my unmanaged swith-Solution
2019-07-22 02:36:37 - last edited 2019-07-23 01:33:09

@PaoloM 

 

The TL-SG1016D is unmanaged switch per you said, configuration is not required, instead, it is plug and play. 

 

And you do not have to worry about the IP conflict issue, just connect them to the modem router to get internet. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#2
Options
3 Reply
Re:Can't reach my unmanaged swith-Solution
2019-07-22 02:36:37 - last edited 2019-07-23 01:33:09

@PaoloM 

 

The TL-SG1016D is unmanaged switch per you said, configuration is not required, instead, it is plug and play. 

 

And you do not have to worry about the IP conflict issue, just connect them to the modem router to get internet. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#2
Options
Re:Re:Can't reach my unmanaged swith
2019-07-22 13:07:26
Thank You. I could try to solve my problem just this morning and I found that the first iussue was a bad ethernet connector. I changet it and now everything work fine. However also the user manual lead me to a wrong way since it simply assert that the switch should be configured.
  0  
  0  
#3
Options
Re:Re:Re:Can't reach my unmanaged swith
2019-07-23 01:32:46

@PaoloM 

 

Thanks for your feedback, glad to hear that you got it fixed finally. 

 

Not sure what is the user manual you read, while for the TL-SG1016D, only the quick installation guide included, theoretically, it won't claim that the switch should be configured. 

 

Anyway, for the unmanaged switch, no configuration needed, it is plug and play.

 

Wish you enjoy the internet with the TP-link switch. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1939

Replies: 3

Related Articles
Can't reach the DHCP server.
10360 0
Can't reach to certain website
1106 0
Oops... We can't reach the cloud server.
2842 0
AC1200 can't reach LAN through VPN
218 0
Reach
253 0
Will it reach my detached garage?
1027 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.