Home Network Community > All Threads > tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
< All Threads

tp-link VR400 - Ethernet port gives 100 MBs instead of 1G

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

tp-link VR400 - Ethernet port gives 100 MBs instead of 1G

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
2019-08-20 05:29:37 - last edited 2019-08-20 06:38:16
Model: Archer VR400  
Hardware Version: V2
Firmware Version:

My ISP speed is 200MBs - gets 200MBs from samsung galaxy S8 througth WIFI.

When I connect CAT6 etherent cable to a computer (tried 2 computers with Ubuntu Linux and Windows) the speed negotiated down to 100MBs:

 

$>sudo mii-tool -v eth0

eth0: negotiated 100baseTx-FD, link ok

product info: vendor 00:07:32, model 17 rev 2  

basic mode:   autonegotiation enabled  

basic status: autonegotiation complete, link ok  

capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD  

advertising:  1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control  

link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

 

$>lspci | grep Eth

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03)

 

$>sudo ethtool eth0
Settings for eth0:
   Supported ports: [ TP ]
   Supported link modes:   10baseT/Half 10baseT/Full 
                           100baseT/Half 100baseT/Full 
                           1000baseT/Full 
   Supported pause frame use: No
   Supports auto-negotiation: Yes
   Supported FEC modes: Not reported
   Advertised link modes:  10baseT/Half 10baseT/Full 
                           100baseT/Half 100baseT/Full 
                           1000baseT/Full 
   Advertised pause frame use: No
   Advertised auto-negotiation: Yes
   Advertised FEC modes: Not reported
   Speed: 100Mb/s
   Duplex: Full
   Port: Twisted Pair
   PHYAD: 0
   Transceiver: internal
   Auto-negotiation: on
   MDI-X: Unknown
   Supports Wake-on: pumbg
   Wake-on: g
   Current message level: 0x00000033 (51)
                drv probe ifdown ifup
   Link detected: yes

 

There is no problem with the computer\cable - because when connecting both computers with the same cable the speed is 1G.

So there is no problem with the computers etherent and the cable. Tried to change port in the router and validated QoS is turned off.

 

Do you have more ideas, why is this happening?

 

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
2019-08-20 09:33:30

@nolim 

 

It seems that the wired negotiation speed between the router and computer limits the actual speed you can get.

 

Try to fix the duplex & speef to 1Gbps to give it a go.

 

For Windows PC, you can go to control panel-network and internet-network and sharing center-change adapter settings-right click on ethernet connection and go to properties, click configure and tab on advanced.

 

As an open system, we are not familiar with the Linux OS, while you can give it a go as well.

 

Besides, please verify the negotiation speed of the VR400; check it under basic-network map page, click on VR400 and then you will get the info.

 

Best regards. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Re:tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
2019-08-24 21:52:39

You are right, the router ports are 100MBs.

The wifi is above 1G, so I was sure the ports are also 1G.

 

Ordered a new router the Archer C7, thanks

  0  
  0  
#3
Options
Re:Re:Re:tp-link VR400 - Ethernet port gives 100 MBs instead of 1G
2019-08-26 02:04:11

@nolim 

 

Thanks for your reply. 

 

Yes, you are right that the 3 LAN ports are 100Mbps ports that is why you won't get the speed higher than 100Mbps.

 

The Archer C7 has the gigabit ports, while there is no DSL port which used to synchronized the DSL connection. 

HARDWARE FEATURES
Interface 4 10/100/1000Mbps LAN Ports
1 10/100/1000Mbps WAN Port
1 USB 2.0 Ports

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1607

Replies: 3

Related Articles
TP-LINK VR400 V2 and V3
2133 0
TP-Link Archer C6 limitando a velocidade do WI-FI em 100 Mbs
28590 11
Enable port forwarding - VR400
4003 0
TP-Link Archer VR400 AC1200 Gigabit VDSL/ADSL 1200Mbps Router port speed problem
1201 0
TP-Link Archer VR400 V2 lost a Port after broadband outage
112 0
TP Link VR400 Work as Repeater
2406 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.