TP-link Archer MR600 Port forwarding not possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TP-link Archer MR600 Port forwarding not possible

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TP-link Archer MR600 Port forwarding not possible
TP-link Archer MR600 Port forwarding not possible
2019-09-17 07:36:45 - last edited 2020-11-24 11:26:40
Model: Archer MR600  
Hardware Version: V1
Firmware Version: 1.1.0 0.9.1 v0001.0 Build 190412 Rel.66770n

I try to do port forwarding for my 4 cameras on Archer 600, so far with no success, The cameras works well on the LAN with the ports I have assigned

I have followed the manual closely to give the cameras fixed address and set the port forwarding under NAT forwarding Virtual Servers.

The ports are closed. I have contaced my ISP- supplier who says there is no restrictions on my connection and I have tried to remove the firewall.

Still no result when I check with the port forwarding tester.

How can I solve this

  0      
  0      
#1
Options
1 Accepted Solution
Re:TP-link Archer MR600 Port forwarding not possible-Solution
2020-11-24 11:00:32 - last edited 2020-11-24 11:26:40

@Tranas 

Hi

My router was bounded by my ISP Telenor. I phoned them. Under APN in my MR 600 I changed from Telenor to internet.public and the problem was solved.

 

Thank you for support

Recommended Solution
  0  
  0  
#7
Options
7 Reply
Re:TP-link Archer MR600 Port forwarding not possible
2019-09-18 02:16:12

@Arvid 

 

What is the current internet IP address of the Archer MR600? 

 

In the same network, please test whether you can access the camera with the WAN IP plus port number.

 

Besides, please use telnet to test:

1. in the same network, please go to run—cmd—telnet lan ip port number 

2. in external network, please run—cmd—telnet wan ip port number

Note: Please show us the pictures of the test results.

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:TP-link Archer MR600 Port forwarding not possible
2019-09-18 16:14:44

@Arvid 

Hi Kevin

My current IP address of the Archer MR600 is: 2.151.132.211.

I have tried to connect one of the cameras on port 1942 from my mobile on my WAN address above with negative result.

 

I have done the telnet test on LAN 192.168.1.103 port 1942 with positive result

 

The telnet test on WAN 2.151.132.211 port 1942 gave negativ result with the message: Could not open connection to the host, on port 1942: Connect failed.

 

I have picture on both telnet tests in Snagit, but I dont know how to send them to you, can't see any possibility to add them in this mail

 

Regards Arvid

  0  
  0  
#3
Options
Re:TP-link Archer MR600 Port forwarding not possible
2019-09-18 19:37:34

@Arvid 

Hi Kevin

I just discovered that I had forgot to set the port back to 1942 in Archer 600.(tried too change ports yesterday)

Taking a new Telnet test on WAN 2.151.132.211 port 1942 I think got a positive response. (blank screen showing up)

 

Still I can't get access to my camera trough my mobilphoneapp which I could with my fibernet and Zyxel router.

 

Regards Arvid

 

 

  0  
  0  
#4
Options
Re:TP-link Archer MR600 Port forwarding not possible
2019-09-19 06:44:16

@Arvid 

Hi again

I have to add a little more to clear the situation

When I try the Port Forward tester on https://www.yougetsignal.com/tools/open-ports/ 

I get the message


2.151.132.211

 
 
Remote Address 
 
   Use Current IP
Port Number
 

Port 1942 is closed on 2.151.132.211.

 

This dont comply with the telnet test who said the port is open (I did the test again today)

 

Regards Arvid

  0  
  0  
#5
Options
Re:TP-link Archer MR600 Port forwarding not possible
2020-11-24 09:52:44

@Arvid I realize that this is an old post - but did you get the MR600 to open ports? Issue with the router or your ISP?? Thanks

  0  
  0  
#6
Options
Re:TP-link Archer MR600 Port forwarding not possible-Solution
2020-11-24 11:00:32 - last edited 2020-11-24 11:26:40

@Tranas 

Hi

My router was bounded by my ISP Telenor. I phoned them. Under APN in my MR 600 I changed from Telenor to internet.public and the problem was solved.

 

Thank you for support

Recommended Solution
  0  
  0  
#7
Options
Re:TP-link Archer MR600 Port forwarding not possible
2021-05-11 20:35:15
what u mean by APN, I cant find that option
  0  
  0  
#8
Options

Information

Helpful: 0

Views: 8232

Replies: 7

Related Articles