Client not reaching DHCP through bridge

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Client not reaching DHCP through bridge

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Client not reaching DHCP through bridge
Client not reaching DHCP through bridge
2020-01-21 21:40:56 - last edited 2020-01-22 06:09:53
Model: AP500  
Hardware Version: V1
Firmware Version: 1.0 beta

I have an ISP router delivering Internet to home.

This is the DHCP, 192.168.1.1, delivering adresses from 192.168.1.10 to 192.168.1.50.

 

I'm using the AP500 in bridge mode to relay the Wifi signal that does not come strong enough through walls. It has a static IP (192.168.1.28)

 

There, I have an Amazon FireTV that connects to the bridge but does not get the Internet.

 

The AP500 emits its own WiFi SSID.

 

If the DHCP is turned off on the AP500, then the FireTv connects, but does not get any IP address (constantly waiting for the IP).

 

If the DHCP is turned on on the AP500, (Gateway 192.168.1.28 delivering adresses from 192.168.1.40.to 192.168.1.50), the FireTv is connected and gets an IP from the AP500 (192.168.1.40). However, it still does not get Internet access. FireTv says "connected with troubles". Indeed, it doesn't show up in the list of the network devices from the main DHCP router.

 

Would you have an idea why the clients connected to the AP500 as a bridge are not seen from the main router?

  0      
  0      
#1
Options
4 Reply
Re:Client not reaching DHCP through bridge
2020-01-22 06:09:37 - last edited 2020-01-22 06:09:53

@Dloki 

 

Hello, with Amazon Fire TV connected to the AP500, what is the IP address and gateway? 

 

Please connect a computer to it directly via ethernet cable to verify whether you can get internet and click here to get the IP address and gateway. 

 

Below is the instruction to set up AP500 as a bridge, please use the main router's wifi password to configure it.

https://www.tp-link.com/support/faq/1073/

 

And please ensure that the firmware is up to date. 

 

What is more, please ensure that there is no specific settings enabled on the main router, like access control or parental control. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Client not reaching DHCP through bridge
2020-01-22 11:41:47

@Kevin_Z 

 

Thank you very much for your answer.

 

I connected a computer as a client, trying both Wifi and RJ45. The computer behaved just like the FireTV's: connected to the AP500 without an Internet connexion.

Although I can mention that I got access to Internet for 1~2 minutes before dropping out. I had to restart the Wifi adapter to recover internet connexion from any AP...

 

The AP500 seems to be correctly configured: its UI is reachable on the local network. Also, the connected devices appear on the DHCP client list of the AP500.
However, only the AP500 appears on the DHCP list of the main router, not its connected clients.

 

  0  
  0  
#3
Options
Re:Client not reaching DHCP through bridge
2020-01-25 18:29:34

Anyone having an idea?

crying

  0  
  0  
#4
Options
Re:Client not reaching DHCP through bridge
2020-04-19 19:48:18

@Dloki I'm experieng the same. Can't find what the issue is, did you ever find a solution to this?

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 3109

Replies: 4

Related Articles