Home Network Community > All Threads > Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
< All Threads

Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-12 07:33:23 - last edited 2020-03-17 06:36:32
Model: Archer A2300  
Hardware Version: V2
Firmware Version: 1.0.0.0.9.1 v0078.0 Build 170814

Hi, I am replacing my current Maxis Home Fibre router to TP-LINK Archer VR600V AC1600 and would like to know what are the setup steps that I need to follow? It seems there is no manual for this. My current Maxis router is Technicolor TG784n V3 flat type without antenna.

 

Could anyone provide me some guidance on setting up this?

 

Thank you in advance!

 

Ivan

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600-Solution
2020-03-16 06:49:08 - last edited 2020-03-17 06:36:32

@Ivan.Wong 

Hi Ivan,

With this connection, you need to switch the working mode on the VR600v to the wireless router mode. You may refer to the instruction below to do the settings.

https://www.tp-link.com/support/faq/1731/

 

If you still can't set it up, please confirm the username& password and VLAN ID with your ISP.

 

Good day.

Recommended Solution
  1  
  1  
#5
Options
10 Reply
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-13 07:56:39

@Ivan.Wong 

 

Hello Ivan, you need connect the internet source to the Archer VR600 first, and then log into the web UI and go to quick setup to configure it. 

 

The internet connection type, username and password are necessary, they are given by ISP, and you can go to next till you finish the configuration.

Note: Some ISPs ask to enable IPTV and enter relatively VLAN ID to make internet work, you can confirm it with ISP. 

 

If it does not work, please tell me how do you connect the ISP to the VR600, by wired cable or DSL line, And the screenshots of the status page and internet page.

 

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-13 09:01:21 - last edited 2020-03-13 09:26:52

@Kevin_Z Hi Kevin, thanks for replying my message.

 

I did use the TP Link Quick Setup for my setup. But I face problem when reached to Testing stage where a Fail status showed on the setup process. 
My connection of the cable are as below:

 

Before

- TM fibre modem LAN port no.3 (default) to Maxis Technicolor TG784n v3 WAN port (red)

- Internet or WiFi everything working fine just that is slow

 

After

- TM fibre modem LAN port no.3 (default) to TP-Link Archer VR600V port no.4 (according to the manual is stated WAN port)

- Run quick setup from the configuration page after connected via TP-Link SSID WiFi 

- The setup stopped at Testing stage with Fail status

- No internet connection

 

I have no idea are there anything that I missed during the setup process?

 

TM to Maxis

 

TM picture 1 to TP Link port:

  0  
  0  
#4
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600-Solution
2020-03-16 06:49:08 - last edited 2020-03-17 06:36:32

@Ivan.Wong 

Hi Ivan,

With this connection, you need to switch the working mode on the VR600v to the wireless router mode. You may refer to the instruction below to do the settings.

https://www.tp-link.com/support/faq/1731/

 

If you still can't set it up, please confirm the username& password and VLAN ID with your ISP.

 

Good day.

Recommended Solution
  1  
  1  
#5
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-16 08:45:58

@Stella.Q Thank you! Let me give it a try and see. Hope it will work.

  0  
  0  
#6
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-16 17:59:47

@Stella.Q Thx Stella, your suggestion worked but needed to enalble the IP V6. Now I have another problem that I need to solve. The VoIP phone. Is not working at all. With tone but I can't dial in any numbers. Any way I can get this phone working? I bought this model is because it comes with VoIP phone ports.

 

Thank you!


Ivan

  0  
  0  
#7
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-17 02:48:58

@Ivan.Wong 

You are welcome Ivan.

 

For the VOIP settings, you may refer to the instruction below. Make sure you put in the correct information from your ISP.

https://www.tp-link.com/support/faq/2020/

 

Good day.

  0  
  0  
#8
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-18 08:11:41

@Stella.Q Hi Stella, tried the steps you provided and it doesn't work. I called up TP Link support and they said TP Link does not support Maxis Fibre VoIP service. Anyway to get it working? I need the phone function for my out going call but now either I use back my Maxis router with the VoIP function or TP Link without the VoIP. 

  0  
  0  
#9
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-03-20 07:34:51

 

Ivan.Wong wrote

@Stella.Q Hi Stella, tried the steps you provided and it doesn't work. I called up TP Link support and they said TP Link does not support Maxis Fibre VoIP service. Anyway to get it working? I need the phone function for my out going call but now either I use back my Maxis router with the VoIP function or TP Link without the VoIP. 

@Ivan.Wong 

It is suggested you contact Maxis to confirm whether you can use third-party modems on the VOIP service, they may have some restrictions.

  0  
  0  
#10
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-04-18 14:10:39
Hi Stella, after checking with Maxis I don't think the VR600v supports the VoIP connection via its RJ11 port. May I know if I could use the VR600v for the Wifi only but retain the Maxis router to be VoIP phone? I need the phone to be used as my house no. I plan to use both routers 1 for Internet and 1 for VoIP phone call. Hope anyone here can help to guide me on how to get the connection works? I tried to connect the Maxis router to one of the Lan port on VR600v but I don't get any ring tone from the phone. My current connection I tried: 1. Unplug the WAN port from Maxis and connect to port 4 (WAN) on VR600v (To get the internet connection from VR600v) 2. Remain my phone jack RJ11 at phone port 1 in Maxis 3. Connect Maxis WAN (Red) port to VR600v port 3 (LAN) 4. Test with phone no tone 5. Swap back the WAN port 4 from VR600v to Maxis WAN (Red) port and test the phone, it works and can call in or out. Hope any expert here can help me to get the connection right?
  0  
  0  
#11
Options
Re:Replacing Maxis Technicolor TG784n V3 with TP-LINK Archer VR600V AC1600
2020-04-22 12:12:07

Great post, a lot of stuff in here i did not know about laugh

  0  
  0  
#12
Options

Information

Helpful: 0

Views: 3879

Replies: 10

Related Articles
Replacing main deco xe75pro with a TP-Link BE9300
282 0
TP-link c5v router from Maxis
2921 0
TP-LINK VR400 V2 and V3
2126 0
how to upgrade in tp link v3 firmware to v6
1417 0
Replacing my poor M3W
748 0
Unable to connect with Maxis
11254 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.