Find admin page after Access Point config

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Find admin page after Access Point config

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Find admin page after Access Point config
Find admin page after Access Point config
2020-04-05 20:25:48 - last edited 2020-04-08 07:57:40
Model: Archer A6  
Hardware Version: V2
Firmware Version:

During out-of-box installation today: added credentials, configured as an access point, then rebooted. Since then the admin page is inaccessible at all three IP addresses. https://tplinkwifi.net/ has the help page; http://192.168.0.1/ links to my primary internet provider router installed in my home; http://192.168.1.1/ times out. Where may I adjust my Archer A6 AC1200 access point wi-fi settings? Thank you!

  0      
  0      
#1
Options
1 Accepted Solution
Re:Find admin page after Access Point config-Solution
2020-04-08 07:57:34 - last edited 2020-04-08 07:57:40

@Bradley 

 

Try to disconnect the Archer A6 from the main router and connect your computer to the Archer A6 directly, after that, you can access the web UI with tplinkwifi.net. 

 

Besides, with Archer A6 connected to the main router, you can log into the web UI of the main router first to get the current IP address of A6, and then you can use this IP address to access the web interface. 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#3
Options
2 Reply
Re:Find admin page after Access Point config
2020-04-05 22:04:32

@Bradley The default in access point mode is that the Archer will take an IP address provided by your main router via DHCP. You should be able to see the address in your main router's DHCP list and then try to connect.

 

However, the tplinkwifi.net should work, but ONLY if you're connecting the phone or whatever you are using to the WiFi of the Archer (maybe you're not connected to it but to the WiFi of the other router). Double check you're connecting to the Archer's WiFi network.

  0  
  0  
#2
Options
Re:Find admin page after Access Point config-Solution
2020-04-08 07:57:34 - last edited 2020-04-08 07:57:40

@Bradley 

 

Try to disconnect the Archer A6 from the main router and connect your computer to the Archer A6 directly, after that, you can access the web UI with tplinkwifi.net. 

 

Besides, with Archer A6 connected to the main router, you can log into the web UI of the main router first to get the current IP address of A6, and then you can use this IP address to access the web interface. 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#3
Options

Information

Helpful: 0

Views: 1909

Replies: 2

Related Articles