Change wifi channel on Deco X60

Change wifi channel on Deco X60

82 Reply
Re:Change wifi channel on Deco X60
2021-02-17 13:25:53
hello there, when will this FW version be available?....using wifi 6 on small channel widths would never get me the speed im looking for or what is advertised on your product.
  0  
  0  
#13
Options
Re:Change wifi channel on Deco X60
2021-02-17 13:50:27

PeekaChuU wrote

....using wifi 6 on small channel widths would never get me the speed im looking for

The 'center' of the channel has (almost) nothing to do with the width of the channel (which is about twice as wide as many other similar products), and is not directly related to the throughput of all the connected devices.

 

Yes, being able to change the 'center' of the channel can help (sometimes dramatically) the throughput of devices if there are other (non-Deco) strong transmitters on or near that same channel.  But the Deco's have a very _large_ channel width -- as well as throughput.

  0  
  0  
#14
Options
Re:Change wifi channel on Deco X60 2021 March time frame
2021-02-28 07:40:50

@TP-Link_Deco  With android (and other os) Wifi Analyzer clearly shows my 3 X60 v1s on 2.4GHz (Ch6) and 5GHz Ch40(42) << what the iPhone and School notebooks connect on for our teens upstairs.

 

We are having disconnects on a 1Gb LAN BackHaul X60 in an upstairs Bedroom.  The girls involved are quite upset since we had Cox Gigablast w rented router working reasonably well but not reaching upstairs.  Not we have good signals and roaming connections with X60s, but the disconnects, which I can see via the app are happening despite home run LAN connects on the X60 upstairs.  

 

Will try reboots again, but the 5GHz 3 X60s always seem to land on Ch40(42), and if we force to 2.4GHz its fairing badly as well with busiers channel 6, which all 3 of the X60 v1s are selecting.  On the reboots, the Main seems to pick, but not good choices, and the 2 other X60s follow.

 

Any help truly appreciated.   I have added them to High Priority, and tried the QOS options, but we are have many devices, many TP-Link plugs :) and avid IT folks in the family crowding both 2.4 and more pushing to 5GHz, WiFi 6

  0  
  0  
#15
Options
Re:Change wifi channel on Deco X60 2021 March time frame
2021-03-01 11:10:23

@cpufox 

Hi,

Have you tried to enable the guest Wi-Fi via 2.4ghz only for smart IoT devices, maybe given a different SSID;

Then leave  the 5ghz only for the main network;

How many Deco units do you have and did only the upstart Deco X60 have the disconnection issue

Would any Deco turn red when the connection lots?

If possible, could you please draw a simple picture of the floor map about the location and distance of each other

Thank you very much and wait for your reply.

  0  
  0  
#16
Options
Re:Change wifi channel on Deco X60
2021-03-17 13:39:44

@TP-Link_Deco  this is a good explanation. Sadly  my ecobee seems to drop signals on 2.4ghz channels below 6. But Id take that as an ecobee problem. 

  0  
  0  
#17
Options
Re:Change wifi channel on Deco X60 2021 March time frame
2021-04-03 20:27:31
I have many 2.4GHz and prefer not to have two SSIDs. Can you provide a link for more information on this advantage. I recently saw, New Firmware 1.5.0 Build 20210121 Rel. 5404 but was waiting to upgrade. Would the new firmware help with the disconnects? All 3 came from Costco and are v1 hardware. The upstairs unit is the one that disconnects the most. It is wired 1Gb which I was relying on for better back haul and the two young adults upstairs are Apple users, iphone, iPad and MacOS. They complain about problems, but it is hard to get more good information from them. I am willing to draw a simple picture but the 3D aspects would be challenging. Main is top of entertainment center (EC, 7ft high) downstairs, midline of home. Vaulted ceilngs to top of home, to right den with no door, open to main living area due to vaulted ceilings, is where switch and home runs connect. I have 2nd port of main deco to 8-port switch for devices in EC, with a hard wire 25ft to den switch and home run (4 ports to upstairs). To right, still first floor, is Master Bedroom (wall) next to another TV where I have no home run anymore when we took out carpet for vinyl. Upstairs a bit to left in bedroom where the disconnects are the most frequent, but has the 1Gb home run from den switch. The time the disconnects are more apparent to me is when I open Deco app on phone, and see it disconnected and immediately reconnect, which I find a quite odd visual. I don't have good information on the number of disconnects, but am willing to send logs to support if you advise. Hope that helps.
  0  
  0  
#18
Options
Re:Change wifi channel on Deco X60 2021 March time frame
2021-04-03 21:38:27

@cpufox 

 

I personally have gone back to a single SSID for both the 2.4 & 5 networks; some of the 2.4 devices require Internet access, not just local, and it was getting to be a configuration pain to attempt to allow both access with the router I was using.

 

However, keeping in mind that I am using the Deco's in Access Point mode (and thus not using the Deco's DHCP services), the by far biggest improvement in the home network stability as recently come from replacing the router (TL-R600VPN) with a Ubiquity EdgeRouter 4.  The issues with disconnects (which, from reading elsewhere, may be due to DHCP server/router issues, not the wireless network itself) seems to have gone away -- caveat: a little less than two weeks of usage so far.

 

When choosing a replacement router (if one goes that way), I would not recommend a TP-Link router, because chances are pretty good that their DHCP service software may use the same "code base" which seems to be causing intermittent issue with other TP-Link routers (Deco, perhaps, as well as the TL-R600VPN router).

 

In addition, because this Ubiquity replacement router is very "high performance" (for a home-type router), I'm also seeing faster/better Internet responses, too (both measured & perceptual).

 

Just yesterday I also did the firmware update on the Deco X60's and there has been nothing negative about it.  After my previous replacement of the separate router, I couldn't say if that firmware update might have any affect on those using them for routing.  (the release notes indicate there should be some improvements)

  0  
  0  
#19
Options
Re:Change wifi channel on Deco X60 2021 March time frame
2021-04-09 17:45:08

@Dan_C. 

 

I too have an ER4 (have had for a while, at first using Ubiquiti AP PRO's but those were slow, had bad range and were flakey).  Switched to Deco M9 Plus set of 3 in wired backhaul mode and was happy.  Great range and stability.  A month later, I had the opportunity to upgrade to the X60's (just a couple days ago).  Same wired backhaul and so far, same great stability, but a little disappointed with the WiFi 6 speeds I'm getting on my iPhone 11 Pro Max and my 2 WiFi 6 laptops. 

 

Learning that the max channel width is 80Mhz on the X60 is disappointing. 

 

Curious what WiFi speeds you're getting on your WiFi 6 devices when at close range to the AP's?

 

ps.  I am on COX Gigablast with a Netgear CM1000 modem.

  0  
  0  
#20
Options
Re:Change wifi channel on Deco X60
2021-04-22 11:39:23 - last edited 2021-04-22 11:50:27

@Dissing re: network speeds

 

I have Comcast cable (not fiber, which is unavailable in our development), and after upgrading to the EdgeRouter 4 I've been getting *better* than 'ISP-rated' Internet speeds.  (At least when testing at non-peak times, like in the morning.)

 

When I test the Internet speed from the Deco App (which uses the Main Deco, which is a wired X60 in my case), I'm often getting ~460 Mb download ... which will reflect the WIRED speed.  When I test from MacBook Pro, direct-wired, I get ~440 Mb download.  So the Deco's, when wired (AP mode), seem to be able to fully access the available network speed.

 

When I test from my iPhone 12 Pro (using Ookla Speedtest app), I get ~430 Mb download -- which is pretty decent in relation to the wired speeds!

  0  
  0  
#21
Options
Re:Change wifi channel on Deco X60
2021-05-14 11:08:28

And? Please be honest, will the firmware come or not? It's been almost a year.  

  1  
  1  
#22
Options
Related Articles