DLNA Blocker with AX50 in Access Mode
I got an AX50 and installed it in Access Mode with a variety of cable connection running through it. It replaced a D-link router that had been doing the same thing for years. The first thing that I noticed is that a DLNA server I have attached to it with a wire was not showing up on the network. There does not seem to be any settings in access mode that block or allow traffic. I "assumed" it should just act as an open switch.
Any ideas?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@Kevin_Z Exacly. I made factory setting on AX50 adn setup new network
AX50 is linked by cable to main router and it now is switch to router mode. To AX50 I set cable to Qnap, TV, XBOX and my laptop. I switch off IPTV
My setup on Huwaei
My setup on AX50
My network on laptop is gone
But if i get comand run and type \\192.168.100.43 it shows my Qnap serwer disc
- Copy Link
- Report Inappropriate Content
So TV and Xbox still cannot access the Qnap serwer disc in this setup?
To locate this issue and try to fix it, we would like to follow up on your case via email. Please check your inbox and provide the information that we need.
- Copy Link
- Report Inappropriate Content
@Kevin_Z Sorry my foult. My Qnap was connected by cable with main router. No it is connected to AX50 and media serwer are working. Perfect.
- Copy Link
- Report Inappropriate Content
@Michal2121 It works for moment and now still Qnap is off. I change adres IP on Qnap on static 192.168.0.5
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Kevin_Z you wrote: Have you tried my previous suggestions that by switching the AX50 to router mode then disable the IGMP snooping and IGMP proxy, then switch it back to AP mode and confirm again? Or, you are suggested to reset the AX50 to factory defaults by holding the reset button until the LEDs flashes off then on, then reconfigure it from scratch, follow the above steps to check again, thanks.
Yes i tried that many times, but there is no difference. There is no NAS/DLNA Client visible in AP Mode, only in Router Mode. Also after resetting it to factory settings.
- Copy Link
- Report Inappropriate Content
This is my networt layout. DLNA from NAS to TV doesn't work at this setup when AX50 is in AP-Mode.
If I plug the TV into the Router and avoid going through the AX50, DLNA immediately works.
If I plug the NAS into AX50, DLNA on TV doesn's work either.
- Copy Link
- Report Inappropriate Content
We have reported the issue to the support engineers, they will likely reach out to you via email to continue to troubleshoot your issue.
- Copy Link
- Report Inappropriate Content
Hi, I have the same issue, AX50 set in AP mode, when DLNA server and DLNA client are both connected through the AX50 the client does not see the server, while if the DLNA server is connected to my router and only the DLNA client is connected to the AX50 in AP mode it works.
Do you have a solution to this issue?
I am in parallel testing another wireless router from another brand, this scenario works perfectly when set in AP mode. I would prefer using the AX50 but I am really hesitating to return it because of this issue.
Thanks
- Copy Link
- Report Inappropriate Content
@Kevin_Z fyi
The technicans also couldn't solve the issue yet.
==================================
I was sent this message from the TP-Link Technical Support:
Dear Customer,
This should be because the DLNA protocol used between the NAS device and the TV is not standard.
Under normal circumstances, devices that support DLNA will discover each other through multicast.
Therefore, if they use the standard DLNA protocol, routers will forward the multicast packets between them when the IGMP snooping is enabled. And they can work normally.
According to the current information, no multicast group is formed between them, and each other needs to be discovered through broadcast.
After turning off the IGMP snooping function, the router will convert all multicast packets into broadcast packets, so they can discover each other and work normally.
It is recommended that you turn off the DHCP and NAT functions on the AX50.
The AX50 can be regarded as working on Access Point Mode after that, and there will be no problem of DLNA ineffective.
Thank you for your understanding.
===================================
When the AX50 is in Router-mode, the NAS is shown on the TV:
IGMP snooping is turned off in Router-mode:
DHCP is also disabled:
NAT settings are disabled:
After switching the AX50 to AP-mode, there is no NAS available on the TV
It seems, the AP-mode blocks the broadcast signal for DLNA somehow. So there is still problem of DLNA ineffectiveness.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 6504
Replies: 42
Voters 0
No one has voted for it yet.