Home Network Community > All Threads > Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
< All Threads

Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2020-08-15 15:42:15 - last edited 2021-03-17 06:10:54
Model: Archer VR900  
Hardware Version: V3
Firmware Version: ArcherVR900(EU)_V3_200708 / 0.5.0 0.9.1 v0069.0 Build 200708 Beta.64424n

Hi, I tried upgrading my VR900 firmware to the latest version to try and improve reliability and it is not able to connect to Plusnet (my ISP). If I downgrade to the previous version it works fine. I've tried a factory reset on the new firmware and setup again but it always has the same issue. If I then apply the older firmware again it works without any changes. This is an export of the system log when it tries to connect:

 

2020-08-15 16:16:00 [6] PPP: sent [PADT session is 1820]
2020-08-15 16:16:00 [6] PPP: sent [PADI Host-Uniq(0x0000135a)]
2020-08-15 16:16:00 [6] PPP: rcvd  [PADO PeerMac(a0-f3-e4-34-f1-60)]
2020-08-15 16:16:00 [6] PPP: sent [PADR Host-Uniq(0x0000135a)]
2020-08-15 16:16:00 [6] PPP: rcvd  [PADS SessionID(0x079f)]
2020-08-15 16:16:00 [5] PPP: Connected to a0:f3:e4:34:f1:60 via interface ptm0.101
2020-08-15 16:16:00 [6] PPP: Using interface ppp1
2020-08-15 16:16:00 [5] PPP: Connect: ppp1 <--> ptm0.101
2020-08-15 16:16:45 [6] PPP: LCP terminated by peer
2020-08-15 16:16:48 [5] PPP: Connection terminated.
2020-08-15 16:16:48 [5] PPP: Release PPP unit success
2020-08-15 16:16:48 [5] PPP: Modem hangup

 

Anyone have any ideas?

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900-Solution
2021-03-17 06:09:34 - last edited 2021-06-04 11:59:51

@Count_Magnus 

Thank you very much for all your kind feedback.

The latest official firmware has fixed this issue already and please make sure that you are running the latest firmware:

ArcherVR900(EU)_V3_210322

https://static.tp-link.com/2021/202103/20210325/Archer_VR900(EU)V3_210322.zip 

 

Thanks a lot.

 

 

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
Recommended Solution
  0  
  0  
#15
Options
12 Reply
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2020-08-19 10:01:49

@Kathy_Z thankyou for looking into this. To answer the questions:

 

1. Its a VDSL 2 connection

2. I did configure VLAN 101 (though when I select Plusnet VDSL as the ISP, it configures that anyway)

3. I tried using both the pre-configured quick setup option and manually configuring as per Plusnet configuration details. Both methods of setup are ok on the old firmware but not the new.

4. I've attached the images of the status and the log direct from a cold boot.

 

 

 

File:
log.txtDownload
  0  
  0  
#3
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2020-08-26 06:21:29

Thank you for this! Guyz you should really double check the options in Services. Some cleaner program disabled mine, so there was no way for my wifi to work. And windows 10 is not smart enough to notice!! Thank you for this advice, man

  0  
  0  
#5
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2020-10-26 13:01:40

@Kathy_Z 

 

I have exactly the same problem as OP on this post. My ISP is talktalk. I can connect fine with firmware Archer VR900(EU)_V3_200228; but I cannot establish pppoe conneciton with firmware Archer_VR900(EU)V3_200708.

 

I have tried factory reset etc with no success. It works with old version firware very time, no success with newer firmware. Same problem as OP/same symptooms, with different ISP.

 

Was a solution ever found - can you help?

 

(I need to use the latest firmaware becuase on older version I have the IP address reservation grayed out bug.)

  0  
  0  
#7
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2020-10-28 09:13:18

@stewartwatson 

Good day,

We would like to forward your case to the senior engineers and please have a check of your message box.

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#8
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-01-16 13:16:14

@Sunshine 

 

Was a solution found? I had exactly the same issue. 

  0  
  0  
#9
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-01-16 15:27:37

@Drave I can only speak for my VR2800, for which the most recent firmware Archer VR2800(EU)_V1_201104 does work with PlusNet.

  0  
  0  
#10
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-01-25 09:56:11 - last edited 2021-01-25 09:56:54

@Kathy_Z / @Sunshine -  Same issue here as @PeteK0 -

 

 

Troubleshooting steps:

  • Reflashed firmware (ArcherVR900(EU)_V3_200708) again
  • Factory reset once flashed 200708 firmware
  • Both quick setup, and manual setup of DSL settings attempted.

 

Same log output as @PeteK0.

 

I notice reading around that certain other VRxxxx routers have had a subsequent matching update pushed that addresses this issue. Has the VR900 been abandoned or is an update coming?

  0  
  0  
#11
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-01-26 11:51:55

@Kathy_Z @Sunshine 

 

I've got the same issue as described above with the VR900 v3 so would be interested if there was ever a fix for this.  The description for the beta firmware describes better performance so it seems worth moving to and testing.

 

Will an update be released that allows successful connection?

  0  
  0  
#12
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-03-10 17:14:27

Hi,

 

Any updates on this? I have the same issue on my VR900. It looks like a fix has already been pushed out for the VR2800/VR600. Can we get the same treatment?

 

Regards,

 

S

  0  
  0  
#13
Options
Re:Cannot connect to ISP (Plusnet) with latest firmware on Archer VR900
2021-03-13 13:59:59

Just tried the same upgrade and I am on Plusnet to and I had the same issues.

 

I have moved back to Archer VR900(EU)_V3_200228

 

But was on Archer VR900(EU)_V3_170303

 

Any help would be appreciated.

 

Thanks

  0  
  0  
#14
Options
12

Information

Helpful: 1

Views: 3160

Replies: 12

Related Articles
Archer VR2800 won't connect to Plusnet with latest firmware
3747 1
AX11000 Cannot connect to internet - ISP is Singtel
2040 0
PPPoE cannot successful connect to ISP with custom settings
262 0
Cannot connect to Internet, ISP is ok
593 0
Connect Archer AX10 to Plusnet Hub 2
956 0
AX1800/Archer VX1800v will not connect to plusnet service
178 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.