Have AC-1750, transmitting slower speed on Wifi though input is 100/100

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Have AC-1750, transmitting slower speed on Wifi though input is 100/100

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Have AC-1750, transmitting slower speed on Wifi though input is 100/100
Have AC-1750, transmitting slower speed on Wifi though input is 100/100
2020-09-02 17:58:08 - last edited 2020-09-04 07:55:06
Model: CAP1750  
Hardware Version:
Firmware Version:

Getting 100/100 from behind however, wifi signals are weaker, probably maximum 50/50 no matter how close you are to the router.

 Also, have AC-1750 router, but not showing up in the list. Wonder why?

  0      
  0      
#1
Options
1 Accepted Solution
Re:Have AC-1750, transmitting slower speed on Wifi though input is 100/100-Solution
2020-09-04 07:55:02 - last edited 2020-09-04 07:55:06

@DevS 

 

Hello,

 

Please verify the model number of the router again, which can be found on its bottom label, it begins as Archer or TL-WRxxx.

 

May I know who is your internet service provider? Without any devices connected, please connect one computer to your modem directly with an Ethernet cable and go to speedtest to run the test for 3 times and show us the screenshots of the test results.

 

Then connect the modem--wireless router--the same computer, and test the speed again. If the wired speed is not good, please try to reset the router to factory defaults and reconfigure it from scratch first.
 

You can refer to the below instruction to narrow down the issue as well.
https://www.tp-link.com/en/faq-2170.html

 

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Have AC-1750, transmitting slower speed on Wifi though input is 100/100-Solution
2020-09-04 07:55:02 - last edited 2020-09-04 07:55:06

@DevS 

 

Hello,

 

Please verify the model number of the router again, which can be found on its bottom label, it begins as Archer or TL-WRxxx.

 

May I know who is your internet service provider? Without any devices connected, please connect one computer to your modem directly with an Ethernet cable and go to speedtest to run the test for 3 times and show us the screenshots of the test results.

 

Then connect the modem--wireless router--the same computer, and test the speed again. If the wired speed is not good, please try to reset the router to factory defaults and reconfigure it from scratch first.
 

You can refer to the below instruction to narrow down the issue as well.
https://www.tp-link.com/en/faq-2170.html

 

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 387

Replies: 1

Related Articles