Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Using Deco M5 AC1300 with TP-ER6120

< All Threads

Using Deco M5 AC1300 with TP-ER6120

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Using Deco M5 AC1300 with TP-ER6120

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

POLYCoach

2020-09-25 14:15:27 - last edited 2020-09-29 11:48:40

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-09-25

Using Deco M5 AC1300 with TP-ER6120

2020-09-25 14:15:27 - last edited 2020-09-29 11:48:40

Model: AC50

Hardware Version: V2

Firmware Version:

I am hoping to connect a Deco M5 AC1300 WiFi mesh system (not purchased yet) to my TP-ER6120 using only the DHCP from the 6120. I am hoping to keep all devices under the same Sub Net Mask. Will the Deco devices automatically connect through the WAN port to the 6120 for IP addresses?

The model above is not correct. Drop down would not allow either the Deco M5 AC1300 or TP-ER6120

1 Accepted Solution

David-TP

2020-09-29 11:47:31 - last edited 2020-09-29 11:48:40

Posts: 12823

Helpful: 1802

Solutions: 1297

Stories: 9

Registered: 2020-04-14

Re:Using Deco M5 AC1300 with TP-ER6120-Solution

2020-09-29 11:47:31 - last edited 2020-09-29 11:48:40

@POLYCoach

Hi, thanks for asking.

In order to find the correct model number for your device, you need to type the specific model in the dialog box, such as Deco M5 or ER6120, then you will be able to choose it.

As per your question, yes, you can connect them as below:

Modem > ER6120 > Deco

Just remember to configure the Deco into an Access Point mode, below is the guide:

https://www.tp-link.com/support/faq/1842/

Hope this makes sense, but let me know if it is not, good days.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Recommended Solution

1 Reply

David-TP

2020-09-29 11:47:31 - last edited 2020-09-29 11:48:40

Posts: 12823

Helpful: 1802

Solutions: 1297

Stories: 9

Registered: 2020-04-14

Re:Using Deco M5 AC1300 with TP-ER6120-Solution

2020-09-29 11:47:31 - last edited 2020-09-29 11:48:40

@POLYCoach

Hi, thanks for asking.

In order to find the correct model number for your device, you need to type the specific model in the dialog box, such as Deco M5 or ER6120, then you will be able to choose it.

As per your question, yes, you can connect them as below:

Modem > ER6120 > Deco

Just remember to configure the Deco into an Access Point mode, below is the guide:

https://www.tp-link.com/support/faq/1842/

Hope this makes sense, but let me know if it is not, good days.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Information

Helpful: 0

Replies: 1

Using Deco M5 AC1300 with TP-ER6120

Using Deco M5 AC1300 with TP-ER6120

Information

Voters 0

Tags