Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > WDS bridging not working properly in Archer C6 (HW v3.20)

< All Threads

WDS bridging not working properly in Archer C6 (HW v3.20)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

WDS bridging not working properly in Archer C6 (HW v3.20)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

gmax

2021-02-18 07:35:02 - last edited 2021-02-23 12:25:10

Posts: 2

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-02-18

WDS bridging not working properly in Archer C6 (HW v3.20)

2021-02-18 07:35:02 - last edited 2021-02-23 12:25:10

Model: Archer C6

Hardware Version: V3

Firmware Version: 1.0.2 Build 20200807 rel.59335(5553)

Hello,

Recently I got Archer C6 router with hardware version 3 and I see that WDS mode is not working as expected. The WDS status is always shown as "Assoc" instead of "Run". Previously I have used Archer C6 with HW version 2 which was working fine with the same root router. May I know what has to be changed in terms of settings to make WDS bridging work in Archer C6 with HW version 3?

P.S : Followed the steps mentioned in this link to setup the WDS bridging https://www.tp-link.com/us/support/faq/1555/

1 Accepted Solution

gmax

LV1

2021-02-23 12:24:21 - last edited 2021-02-23 12:25:10

Posts: 2

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-02-18

Re:WDS bridging not working properly in Archer C6 (HW v3.20)-Solution

2021-02-23 12:24:21 - last edited 2021-02-23 12:25:10

Hello @Kevin_Z

Thanks for your reply.

We just realized that the issue is with the root router as it was not able to handle the load when connection exceeds certain number. By disconnecting all other connection to root router and keeping only C6 active, we see that C6 is able to establish the WDS bridging.

Recommended Solution

3 Reply

Kevin_Z

2021-02-23 09:30:51

Posts: 21782

Helpful: 5158

Solutions: 2575

Stories: 21

Registered: 2018-12-24

Re:WDS bridging not working properly in Archer C6 (HW v3.20)

2021-02-23 09:30:51

@gmax

Hi, may I have the model number of the main/root router? You may try to change the wireless channel on that router to a different one, such as 6 or 11, then reboot the main, and reconfigure the C6 to connect to it.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

gmax

LV1

2021-02-23 12:24:21 - last edited 2021-02-23 12:25:10

Posts: 2

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-02-18

Re:WDS bridging not working properly in Archer C6 (HW v3.20)-Solution

2021-02-23 12:24:21 - last edited 2021-02-23 12:25:10

Hello @Kevin_Z

Thanks for your reply.

Information

Helpful: 0

Replies: 3

WDS bridging not working properly in Archer C6 (HW v3.20)

WDS bridging not working properly in Archer C6 (HW v3.20)

Information

Voters 0

Tags