Home Network Community > All Threads > Issues with VPN over 5g, works fine at 2.4ghz
< All Threads

Issues with VPN over 5g, works fine at 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Issues with VPN over 5g, works fine at 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Issues with VPN over 5g, works fine at 2.4ghz
Issues with VPN over 5g, works fine at 2.4ghz
2021-10-06 06:21:28
Model: Archer C9  
Hardware Version: V5
Firmware Version: 1.2.4 Build 20190403 rel.63869(4555)

Hello, 

 

I am facing a very strange problem since I changed my router at home. I need to use Cisco VPN client to connect to my office and I have had no issues before. 

With my new router (archer C9 v5.1) I can connect only using the 2.4ghz band, the 5ghz band does not seem to agree with the company VPN ...

Note 1: the IT admin at my office said that nothing has changed on their end  

Note 2: I can connect without any issues if using the 2.4ghz band on the same router

Note 3: I used to be able to connect on 5ghz with my previous router (again TP-LINK, but older).

 

All these make me believe it might be something with the router itself, can you help me here? 

Regards,

Spasov

  0      
 
  0      
 
#1
Options
3 Reply
Re:Issues with VPN over 5g, works fine at 2.4ghz
2021-10-06 13:33:23

@ISpasov 

 

There's no particular reason for that. Both bands are bridged with device's LAN ports.

The only difference between wireless bands could be the wireless security settings:

Use these for both bands and test again to see if any difference.

If that doesn't help try disabling the DoS protection and test again:

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Issues with VPN over 5g, works fine at 2.4ghz
2021-10-06 14:35:16

@terziyski , thanks! 

Both bands are "AUTO" in my setup .. and DoS would not be different for 2.4 vs 5, would it? 

 

I know that VPNs work on a level that should not in any way or form be influenced by the bandwidth of my wireless, but ... the router is the only different thing in the setup from last week and now :(

 

Sigh, I will disable the DoS and try again ...

Unfortunately I would need to stay on Auto as I have old devices that do not understand AES :) 

  0  
  0  
#3
Options
Re:Issues with VPN over 5g, works fine at 2.4ghz
2021-10-06 15:30:44

@ISpasov 

 

You're right, the DoS protection should be the same for both bands - it was just a shot in the dark, cause that behavior is strange.

If your old router wireless security settings were both on Auto (because of your older devices) and it worked, then that shouldn't be an issue too.

Have you tested to build the VPN through a cable connection ?

I really can't think of anything else.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 5602

Replies: 3

Related Articles
AX50 no 2.4ghz but 5ghz works fine
635 0
unstable VPN via WIFI, wired works fine
639 0
Wifi works fine for a few hours then authentication issues
465 0
Archer C3150 v2 2.4 do not works but 5g is fine
772 0
5 Ghz doesn't work in archer TX50E, while 2.4 Ghz works just fine
2998 0
WiFi connection 5ghz works fine but 2.4ghz doesnt work
794 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.