Home Network Community > All Threads > Does Access Point Mode Use Main Router IP Address?
< All Threads

Does Access Point Mode Use Main Router IP Address?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Does Access Point Mode Use Main Router IP Address?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Does Access Point Mode Use Main Router IP Address?
Does Access Point Mode Use Main Router IP Address?
2022-06-09 13:05:55 - last edited 2022-06-10 15:03:03
Tags: #Access Point Mode
Model: TL-WR940N  
Hardware Version:
Firmware Version:

So i set my TL-WR940N router to access point mode and use it to extend Wifi from a main router using cable from the main router LAN port. The WR940N default gateway is 192.168.0.1 as mentoined in the manual book and website. At some point the router didn't provide internet access yet the light is blue which mean its still get internet from the main router. I tried to change some setting from the default gateway and it didn't fix the probelm, so i decided to reset the WR940N. Somehow the router setting can't be accessed again both from 192.168.0.1 and tplinkwifi.net. Later I found out that the devices connected to the WR940N router have IP address based on the main router. When entering the main router default gateway, it show the main router setting instead.

 

Is that how access point mode supposed to work? 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Does Access Point Mode Use Main Router IP Address? -Solution
2022-06-09 16:19:50 - last edited 2022-06-10 15:03:03

  @Alex_03 

 

You can refer this guide for configuring TL-WR940N in AP mode. Choose Case 1 or 2 according to your TL-WR940N version.

In AP mode the DHCP server of the TL-WR940N is disabled, while the IP address of the TL-WR940N should be in the main router's LAN subnet.

If TL-WR940N has a dedicated AP mode then connect your main router LAN port to TL-WR940N WAN port, otherwise the connection should be LAN to LAN.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  2  
  2  
#2
Options
2 Reply
Re:Does Access Point Mode Use Main Router IP Address? -Solution
2022-06-09 16:19:50 - last edited 2022-06-10 15:03:03

  @Alex_03 

 

You can refer this guide for configuring TL-WR940N in AP mode. Choose Case 1 or 2 according to your TL-WR940N version.

In AP mode the DHCP server of the TL-WR940N is disabled, while the IP address of the TL-WR940N should be in the main router's LAN subnet.

If TL-WR940N has a dedicated AP mode then connect your main router LAN port to TL-WR940N WAN port, otherwise the connection should be LAN to LAN.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  2  
  2  
#2
Options
Re:Does Access Point Mode Use Main Router IP Address?
2022-06-10 15:02:51

  @terziyski thank you for the reply, but both case didn't work for me and the only way to access configuration site is by disconnecting the WR940N WAN port, at least there's a way to configure it. And thank you for the confirmation of the IP address

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 961

Replies: 2

Tags

Access Point Mode
Related Articles
Access Point Mode or Router Mode
1163 0
Use LAN ports when in Access Point Mode
4564 0
IP address when Deco x90 is in access point mode
801 0
Using the router in access point mode
1285 0
router to use as an Access point - True gigabit fiber
2115 0
Problem with access point mode
562 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.