Deco M5 (3.2) WiFi Performance issues in different units.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco M5 (3.2) WiFi Performance issues in different units.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M5 (3.2) WiFi Performance issues in different units.
Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-10 15:44:00 - last edited 2022-10-10 15:52:09
Model: Deco M5  
Hardware Version: V3
Firmware Version: 1.6.1 Build 20220818 Rel. 36456

Hi,

 

I have a 3 set Deco M5(3.2), all running last firmware - (1.6.1 Build 20220818 Rel. 36456). All of then connected by ethernet cat 5e cables.

 

Router                 Main

[####} ---------->Deco1-------------->Deco2------------->Deco3

 

Well, the unit Deco3 has powerfull wifi signal and reaches the max internet speed (350Mbps). All other units has low wifi signal and speed reaches max 30Mbps no matter how close the clients were from the units.

 

Most of the devices tries to connect to Deco3 unit no matter how far they are.

 

Now is the interesting thing, I swapped Deco2 and Deco3 units to test if it’s the location or if something are generating interference, but Deco3 still having the strongest signal and speed and the other units poor performance.

 

Router                 Main

[####} ---------->Deco1-------------->Deco3------------->Deco2

 

The last test I did, I turned off one unit and swap the positions with same results, no matter were the units are, Deco3 has a way stronger wifi signal and others poor performance.

 

Router                                                Main

[####} ---------------------------------->Deco1-------------->Deco3

 

I also tried to remove Deco2 and add it again, but nothing changed.

 

During the tests I checked in the Deco App were the clients were connecting and also force then to connect in Deco1 and 2 to test the speed.

 

There are no features enabled (QoS,Antivirus, Parental Control)

 

 

Any ideas?? Could be that I got 2 faulty units??

 

Thanks,

 

Carlos Sotelo.

 

  3      
  3      
#1
Options
7 Reply
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-10 16:10:25 - last edited 2022-10-10 16:12:57

  @csotelo 

 

It is unlikely but possible that you've got two defective units. Here are steps to check if your Deco M5 work correctly.

 

1. Verify Ethernet backhaul.

 

You said you connected all Deco with Ethernet cable, but have you checked they use Ethernet? In Deco app, check what it says under Signal Source for each Satellite Deco. When Satellite Deco uses Ethernet, you'll see this:

 

 

2. Slow WiFi.

 

30Mbps sounds like 2.4GHz speed. To see if your Deco can broadcast on 5GHz, turn off 2.4GHz on Main Network:

 

 

Check if your devices can connect to Satellite Decos after that and at what speed. If they can't at all, your Deco might not be broadcasting 5GHz WiFi signal.

 

3. Use WiFi analyzer app on smartphone

 

You can install WiFi analyzer app on smartphone to see what Deco units broadcast at which bands and with what signal strength. I am using WiFiman from ubiquiti and this is what it tells me about my Deco mesh (with 2.4GHz turned off):

 

 

Obviously, I was standing near Deco Node 1 when running this test.

 

You can bring all three Deco to the same room, connect them by short Ethernet cables, make half-circle out of them, put smartphone with WiFi analyzer app in the middle of that half-circle, run WiFi analyzer and it should report all three Deco with very close levels of signal for 2.4GHz and for 5 GHz. If one or two Deco have much weaker signals than Deco3, either 2.4GHz or 5GHz, it may point at issue with Deco hardware.

 

For reference, this is explanation of what is good signal level:

 

  1  
  1  
#2
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-10 18:59:16

 Hi  @Alexandre,

 

Thanks for your response.

 

1 – I had verified this, 2 and 3 show source from 1, ethernet.

 

2 -  You got it right! Units 1 and 2 are not broadcasting 5G network. Turning off 2.4 network, only Deco3 is visible.

 

Do you have any idea on how to enable 5G network on these 2 units??

 

60-A4-B7-B8-33-EA – Deco1

60-A4-B7-B8-30-3E – Deco2

60-A4-B7-B8-33-EF – Deco3

 

 

 

3 -  By now I tested 2 and 3, both 1 meter appart, phone in the middle of the two.

 

 

 

Only getting really close to unit 2 the phone registered the 5G channel. If I got 1 meters appart it gone.

 

Is there any way to factory reset besides the back button? (which I already did)

 

Thanks,

 

Carlos Sotelo

 

 

 

 

 

  0  
  0  
#3
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-10 19:31:47

  @csotelo 

 

From your tests it does appear you have two defective Deco M5 units. If you can, return them or send for replacement under the warranty.

 

Forcing factory reset will not fix defective hardware. Still, there is another way to factory reset Deco units: How Do I Reboot or Reset My System?

  0  
  0  
#4
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-11 01:15:23

Thanks a lot for Alex's suggestion and they are very useful.

  @csotelo Welcome to the community.

Apart from these ideas. Did you just get the Deco M5? Since 1.6.1 was just related several weeks ago, Not sure it might be related and it would be better to double-check.

Have you noticed this issue since out of the box?  if not, would there be any changes recently?

 

Thank you very much.

Best regards.

 

 

 

 

  0  
  0  
#5
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-11 14:56:46

Hi   @David-TP ,

 

I did the setup at September. 18, just Deco1 and Deco3 because I didn´t had the cable to last unit.

 

Router                 Main

[####} ---------->Deco1--------------> Deco3

 

After initial setup, the app requested to upgrade the firmware, I guess for 1.6.0,  and a few days after it requested again, for 1.6.1. (II´m in Brazil).

 

I remember to test speed at unit 1 after setup and I got 80% of full internet speed. On the unit 3, I got 100%.

 

A few days ago I noticed performance degradation close to unit 1, and started to use wifi from the  ISP router.

 

In the weekend I got the cable for last unit, added unit 2 and noticed that all clients still connecting to unit 3, so I started the troubleshooting swapping the units.

 

Yesterday I got unit 2 downgraded to 1.6.0 and then to 1.5.7 (using tftp) but nothing changed, still low signal.

 

Thanks,

 

Carlos Sotelo

  2  
  2  
#6
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-12 03:46:59

  @csotelo 

Thank you very much for the confirmation. In this way, the firmware is not the problem.

Have you tried to set Deco 3 as the main Deco and check whether there would be any difference between Deco 1 and 2 when they are working as satellite Mesh nodes?

If Deco 1 and 2 were still the same, I am afraid you might have two broken units.

Thanks a lot.

Best regards.

 

  0  
  0  
#7
Options
Re:Deco M5 (3.2) WiFi Performance issues in different units.
2022-10-12 19:47:06

 Hi  @David-TP ,

 

I did the test, changed Deco3 to main and nothing changed.

 

I put unit 1 and 2 together, phone about a meter away and the signal is weaker than deco3 that is about 10 meters away behind a brick wall.

 

60-A4-B7-B8-33-EA – Deco1

60-A4-B7-B8-30-3E – Deco2

60-A4-B7-B8-33-EE – Deco3

 

 

 

I also got a new deco unit (Deco-n1), did the setup, firmware upgrade and in this one the Wifi works great! It reaches 100% of internet speed as Deco3.

 

28-87-BA-89-E9-97 - Deco-n1

60-A4-B7-B8-33-EF - Deco3

 

 

I´ll contact the local support to send the faulty units for replacement under the warranty. Never had a good experience doing this, I hope it will be different with TP Link. I´ll send the link of this thread in my request and report back here the results.

 

I´m putting the SN of the units here, maybe it helps TP Link to address quality issues. Never had the “lucky” of get two defective electronics out of the box like this.

 

 

 

I´d like to thanks @Alexandre and @David-TP for the help in the troubleshooting.

 

Carlos Sotelo.

 

 

 

 

  2  
  2  
#8
Options