Archer C4000 - unexpected router factory reset

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C4000 - unexpected router factory reset

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C4000 - unexpected router factory reset
Archer C4000 - unexpected router factory reset
2024-04-19 23:12:04
Model: Archer C4000  
Hardware Version: V2
Firmware Version: 1.1.5 Build 20231010 rel.60239(5553)

Hi,

 

With my router Archer C4000, I normally turn it off at the end of the day and turn it back on in the morning.

 

Occasionally, I notice that the device seems to undergo a complete factory reset so that when I turn it on, I have to use a network cable to connect to it and re-configure it completely to set admin password, wifi passwords, etc.

 

It happened again this morning and I saw these unexpected system log entries from yesterday afternoon:

 

2024-04-19 15:42:24 traffic-stats[7094]: <6> 269004 stats reset
2024-04-19 15:42:24 network[24346]: <6> 290005 Reload config
2024-04-19 15:42:23 nat[24512]: <6> 211501 Initialization succeeded
2024-04-19 15:42:23 nat[24512]: <6> 211501 Initialization succeeded
2024-04-19 15:42:23 network[24346]: <6> 290004 Disconnect interface wan
2024-04-19 15:42:22 network[24346]: <6> 290004 Disconnect interface internet
2024-04-19 15:42:21 network[24346]: <6> 290100 Set WAN protocol to dhcp, operation is write
2024-04-19 15:42:21 iptv[24346]: <6> 216503 Function disabled
2024-04-19 15:39:39 led-controller[1564]: <6> 288051 Start to run WAN1_ON
2024-04-19 15:39:39 led-controller[1564]: <6> 288051 Start to run WAN0_OFF
2024-04-19 15:39:39 led-controller[1564]: <6> 288051 Start to run LAN_ON
2024-04-19 15:39:37 led-controller[1564]: <6> 288051 Start to run WAN1_ON
2024-04-19 15:39:37 led-controller[1564]: <6> 288051 Start to run WAN0_OFF
2024-04-19 15:39:37 led-controller[1564]: <6> 288051 Start to run LAN_OFF
2024-04-19 15:39:27 led-controller[1564]: <6> 288051 Start to run WAN1_ON
2024-04-19 15:39:27 led-controller[1564]: <6> 288051 Start to run WAN0_OFF
2024-04-19 15:39:27 led-controller[1564]: <6> 288051 Start to run LAN_ON
2024-04-19 15:34:09 led-controller[1564]: <6> 288051 Start to run WAN1_ON
2024-04-19 15:34:09 led-controller[1564]: <6> 288051 Start to run WAN0_OFF
2024-04-19 15:34:09 led-controller[1564]: <6> 288051 Start to run LAN_OFF

 

What could be causing these unexpected log entries and are they related to the factory reset observed in the morning? There was no issue with the router throughout yesterday even after the time on these log entries.

 

The device is already using the latest firmware 1.1.5 Build 20231010 rel.60239(5553)

  0      
  0      
#1
Options
1 Reply
Re:Archer C4000 - unexpected router factory reset
2024-04-22 10:03:38

  @Starion 

 

Hi, normally a power cycle will clear previous logs, so normally after a reboot and even an unexpected factory reset, there should be no yesterday's logs. 

Please check the router system time to see if it is correct.

 

Regarding the log contents, it is not related to factory reset, the LED controller related logs mean the light status on the router, such as WAN 0 OFF, WAN 1 ON means Internet LED is green, so it seems no issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 376

Replies: 1

Related Articles